C
HAPTER
39
| VLAN Commands
Configuring VLAN Interfaces
– 934 –
D
EFAULT
S
ETTING
All frame types
C
OMMAND
M
ODE
Interface Configuration (Ethernet, Port Channel)
C
OMMAND
U
SAGE
When set to receive all frame types, any received frames that are untagged
are assigned to the default VLAN.
E
XAMPLE
The following example shows how to restrict the traffic received on port 1
to tagged frames:
Console(config)#interface ethernet 1/1
Console(config-if)#switchport acceptable-frame-types tagged
Console(config-if)#
R
ELATED
C
OMMANDS
switchport allowed
vlan
This command configures VLAN groups on the selected interface. Use the
no
form to restore the default.
S
YNTAX
switchport allowed vlan
{
add
vlan-list
[
tagged
|
untagged
] |
remove
vlan-list
}
no switchport allowed vlan
add
vlan-list
- List of VLAN identifiers to add.
remove
vlan-list
- List of VLAN identifiers to remove.
vlan-list
- Separate nonconsecutive VLAN identifiers with a comma
and no spaces; use a hyphen to designate a range of IDs. Do not
enter leading zeros. (Range: 1-4093).
D
EFAULT
S
ETTING
All ports are assigned to VLAN 1 by default.
The default frame type is untagged.
C
OMMAND
M
ODE
Interface Configuration (Ethernet, Port Channel)
C
OMMAND
U
SAGE
u
A port, or a trunk with switchport mode set to
hybrid
, must be
assigned to at least one VLAN as untagged.
u
If a trunk has switchport mode set to
trunk
(i.e., 1Q Trunk), then you
can only assign an interface to VLAN groups as a tagged member.
Summary of Contents for DG-GS4826S
