Page 33
The
Presets
screen has three tabs:
1. Label
To modify a preset name:
a)
Select an
preset
and select its
label
.
b)
Enter the new
preset name
and select the
OK
button.
2. Control
You can activate, deactivate, or configure a selected preset. The
procedures differ depending on the CLC setting type, as follows:
Threshold Trigger
a)
Activate or deactivate a preset by selecting the
ACTIVATE
or
DEACTIVATE
button.
An orange rectangle is displayed for activated preset and a
blue rectangle for a deactivated preset.
b)
Select the
LOW LEVEL
or
HIGH LEVEL
button to view
the current
Low Level Set Point
or
High Level Set Point
,
respectively. Adjust the set points by using the slider and
selecting the Set button. When setting the
High Level Set
Point
, first select
Interior
or
Exterior
, as exterior values
need larger ranges, then adjust the set point.
c)
Select the
MODIFY
button to view or modify sensor
parameters, as follows:
1. Triggering Preset
- display any of the CLC triggering
presets associated with the output.
2. Daylight Sensor
- select the associated
link
to modify
the controlling sensor. Next, select the new
sensor
.
3. CLC Function
- select the associated
link
to modify the
CLC type. Next, select the
Open Loop
or
Closed Loop
option and select the
OK
button.
4. High Level Target
- select the associated
link
to modify
the high level target, which is the relay output that is
turned on when the light levels exceed the High Level
Set Point. Next, select the new
output
.
5. Test Mode
- select the associated
link
to enable or
disable the test mode. By default, this option is turned
off. If this option is enabled, there is no delay time
between light level readings.
Constant Lighting Controller
32
Dialog® Lighting Control System
Constant Lighting Controller
The
Presets
screen has three tabs:
1.
Label
To modify a preset name:
a)
Select an
preset
and select its
label
.
b)
Enter the new
preset name
and select the
OK
button.
2.
Control
You can activate, deactivate, or configure a selected preset. The procedures
differ depending on the CLC setting type, as follows:
Threshold Trigger
a)
Activate or deactivate a preset by selecting the
ACTIVATE
or
DEACTIVATE
button.
An orange rectangle is displayed for activated preset and a blue
rectangle for a deactivated preset.
b)
Select the
LOW LEVEL
or
HIGH LEVEL
button to view the current
Low Level Set Point
or
High Level Set Point
, respectively. Adjust
the set points by using the slider and selecting the
Set
button. When
setting the
High Level Set Point
, first select
Interior
or
Exterior
, as
exterior values need larger ranges, then adjust the set point.
c)
Select the
MODIFY
button to view or modify sensor parameters, as
follows:
1. Triggering Preset
- display any of the CLC triggering presets
associated with the output.
2. Daylight Sensor
- select the associated
link
to modify the
controlling sensor. Next, select the new
sensor
.
3. CLC Function
- select the associated
link
to modify the CLC type.
Next, select the
Open Loop
or
Closed Loop
option and select the
OK
button.
4. High Level Target
- select the associated
link
to modify the high
level target, which is the relay output that is turned on when
the light levels exceed the High Level Set Point. Next, select
the new
output.
5. Test Mode
- select the associated
link
to enable or disable the test
mode. By default, this option is turned off. If this option is enabled,
there is no delay time between light level readings.
C
M
Y
CM
MY
CY
CMY
K
32
Dialog® Lighting Control System
Constant Lighting Controller
The
Presets
screen has three tabs:
1.
Label
To modify a preset name:
a)
Select an
preset
and select its
label
.
b)
Enter the new
preset name
and select the
OK
button.
2.
Control
You can activate, deactivate, or configure a selected preset. The procedures
differ depending on the CLC setting type, as follows:
Threshold Trigger
a)
Activate or deactivate a preset by selecting the
ACTIVATE
or
DEACTIVATE
button.
An orange rectangle is displayed for activated preset and a blue
rectangle for a deactivated preset.
b)
Select the
LOW LEVEL
or
HIGH LEVEL
button to view the current
Low Level Set Point
or
High Level Set Point
, respectively. Adjust
the set points by using the slider and selecting the
Set
button. When
setting the
High Level Set Point
, first select
Interior
or
Exterior
, as
exterior values need larger ranges, then adjust the set point.
c)
Select the
MODIFY
button to view or modify sensor parameters, as
follows:
1. Triggering Preset
- display any of the CLC triggering presets
associated with the output.
2. Daylight Sensor
- select the associated
link
to modify the
controlling sensor. Next, select the new
sensor
.
3. CLC Function
- select the associated
link
to modify the CLC type.
Next, select the
Open Loop
or
Closed Loop
option and select the
OK
button.
4. High Level Target
- select the associated
link
to modify the high
level target, which is the relay output that is turned on when
the light levels exceed the High Level Set Point. Next, select
the new
output.
5. Test Mode
- select the associated
link
to enable or disable the test
mode. By default, this option is turned off. If this option is enabled,
there is no delay time between light level readings.
C
M
Y
CM
MY
CY
CMY
K
32
Dialog® Lighting Control System
Constant Lighting Controller
The
Presets
screen has three tabs:
1.
Label
To modify a preset name:
a)
Select an
preset
and select its
label
.
b)
Enter the new
preset name
and select the
OK
button.
2.
Control
You can activate, deactivate, or configure a selected preset. The procedures
differ depending on the CLC setting type, as follows:
Threshold Trigger
a)
Activate or deactivate a preset by selecting the
ACTIVATE
or
DEACTIVATE
button.
An orange rectangle is displayed for activated preset and a blue
rectangle for a deactivated preset.
b)
Select the
LOW LEVEL
or
HIGH LEVEL
button to view the current
Low Level Set Point
or
High Level Set Point
, respectively. Adjust
the set points by using the slider and selecting the
Set
button. When
setting the
High Level Set Point
, first select
Interior
or
Exterior
, as
exterior values need larger ranges, then adjust the set point.
c)
Select the
MODIFY
button to view or modify sensor parameters, as
follows:
1. Triggering Preset
- display any of the CLC triggering presets
associated with the output.
2. Daylight Sensor
- select the associated
link
to modify the
controlling sensor. Next, select the new
sensor
.
3. CLC Function
- select the associated
link
to modify the CLC type.
Next, select the
Open Loop
or
Closed Loop
option and select the
OK
button.
4. High Level Target
- select the associated
link
to modify the high
level target, which is the relay output that is turned on when
the light levels exceed the High Level Set Point. Next, select
the new
output.
5. Test Mode
- select the associated
link
to enable or disable the test
mode. By default, this option is turned off. If this option is enabled,
there is no delay time between light level readings.
C
M
Y
CM
MY
CY
CMY
K
32
Dialog® Lighting Control System
Constant Lighting Controller
The
Presets
screen has three tabs:
1.
Label
To modify a preset name:
a)
Select an
preset
and select its
label
.
b)
Enter the new
preset name
and select the
OK
button.
2.
Control
You can activate, deactivate, or configure a selected preset. The procedures
differ depending on the CLC setting type, as follows:
Threshold Trigger
a)
Activate or deactivate a preset by selecting the
ACTIVATE
or
DEACTIVATE
button.
An orange rectangle is displayed for activated preset and a blue
rectangle for a deactivated preset.
b)
Select the
LOW LEVEL
or
HIGH LEVEL
button to view the current
Low Level Set Point
or
High Level Set Point
, respectively. Adjust
the set points by using the slider and selecting the
Set
button. When
setting the
High Level Set Point
, first select
Interior
or
Exterior
, as
exterior values need larger ranges, then adjust the set point.
c)
Select the
MODIFY
button to view or modify sensor parameters, as
follows:
1. Triggering Preset
- display any of the CLC triggering presets
associated with the output.
2. Daylight Sensor
- select the associated
link
to modify the
controlling sensor. Next, select the new
sensor
.
3. CLC Function
- select the associated
link
to modify the CLC type.
Next, select the
Open Loop
or
Closed Loop
option and select the
OK
button.
4. High Level Target
- select the associated
link
to modify the high
level target, which is the relay output that is turned on when
the light levels exceed the High Level Set Point. Next, select
the new
output.
5. Test Mode
- select the associated
link
to enable or disable the test
mode. By default, this option is turned off. If this option is enabled,
there is no delay time between light level readings.
C
M
Y
CM
MY
CY
CMY
K
To modify a preset name:
a)
1.
2.
3.
4.
5.
c)
b)
