manualshive.com logo in svg

Dialog WLC-4150-C, Field Manual

The Dialog WLC-4150-C field manual provides comprehensive guidance on setting up and operating this powerful device. You can download the manual for free from manualshive.com, ensuring you have all the information you need at your fingertips. Get your hands on this essential manual today to maximize the potential of your WLC-4150-C.

Share
Download
background image

Page 29

The Groups screen has three tabs:

1. Label

To modify a group name:

a)

  Select an output and select its label.

b)

  Enter the new preset name and select the OK button.

2. Control

You can activate, deactivate, or configure a selected group. The 

procedures differ depending on the CLC setting type, as follows:

Threshold Trigger

a)

  Activate or deactivate an output by selecting the 

ACTIVATE 

or 

DEACTIVATE

 button.

An orange rectangle is displayed for activated modes and a 

blue rectangle for deactivated modes.

b)

  Select the 

LOW LEVEL

 or 

HIGH LEVEL

 button to view 

the current 

Low Level Set Point

 or 

High Level Set Point

, 

respectively. Adjust the set points by using the slider and 

selecting the 

Set

 button.

c)

  Select the 

MODIFY

 button to view or modify sensor 

parameters, as follows:

1.   Triggering Preset

 - display any of the CLC triggering 

presets associated with the output.

2.   Daylight Sensor

 - select the associated 

link

 to modify 

the controlling sensor. Next, select the new 

sensor

.

3.   CLC Function

 - select the associated link to modify the 

CLC type. Next, select the 

Open Loop

 or 

Closed Loop 

option and select the 

OK

 button.

4.  High Level Target

 - select the associated 

link

 to modify 

the high level target, which is the relay output that is 

turned on when the light levels exceed the High Level 

Set Point. Next, select the 

new output

.

5.  Test Mode

 - select the associated 

link

 to enable or 

disable the test mode. By default, this option is turned 

off.  If this option is enabled, there is no delay time 

between light level readings.

Open Loop

a)

  Activate or deactivate a selected dimmer group by selecting 

the 

ACTIVATE

 or 

DEACTIVATE

 button.

An orange rectangle is displayed for activated modes and a 

blue rectangle for deactivated modes.

b)

  Select the 

DIMMER

 button to adjust the dimmer out dimming 

level Set Point. This is set as a percentage. Use the slider to 

adjust the level and select the Set button. In the case when 

the there are multiple dimmer outputs controlled by the same 

sensor, this value is the dimmer RATIO.

Constant Lighting Controller

28

Dialog® Lighting Control System

The Groups screen has three tabs:

1. 

Label
To modify a group name:

 

a) 

Select an output and select its label.

 

b) 

Enter the new preset name and select the OK button.

2. 

Control

You can activate, deactivate, or configure a selected group. The procedures 

differ depending on the CLC setting type, as follows:

Threshold Trigger

 

a) 

Activate or deactivate an output by selecting the 

ACTIVATE

 or   

 

 

DEACTIVATE 

button.  

  An orange rectangle is displayed for activated modes and a blue rectangle 

  for deactivated modes. 

 

b) 

Select the 

LOW LEVEL

 or 

HIGH LEVEL

 button to view the current 

Low  

  Level Set Point

 or 

High Level Set Point

, respectively. Adjust the set   

  points by using the slider and selecting the 

Set

 button. 

 

c) 

Select the 

MODIFY 

button to view or modify sensor parameters, as follows:

    1. 

Triggering Preset 

- display any of the CLC triggering presets 

 

 

    associated with the output.

    2. 

Daylight Sensor

 - select the associated 

link

 to modify the controlling   

    sensor. Next, select the new 

sensor

. 

    3. 

CLC Function

 - select the associated 

link

 to modify the CLC type. Next, 

    select the 

Open Loop

 or 

Closed Loop

 option and select the 

OK

    4. 

High Level Target

 - select the associated 

link

 to modify the high level   

    target, which is the relay output that is turned on when the light levels 

 

    exceed the High Level Set Point. Next, select the 

new output.

 

    5. 

Test Mode

 - select the associated 

link

 to enable or disable the test   

    mode. By default, this option is turned off.  If this option is enabled, there 

    is no delay time between light level readings. 

  Open Loop

a) 

Activate or deactivate a selected dimmer group by selecting the 

ACTIVATE

or 

DEACTIVATE 

button.  

An orange rectangle is displayed for activated modes and a blue rectangle 

for deactivated modes. 

b) 

Select the 

DIMMER

 button to adjust the dimmer out dimming level Set 

Point. This is set as a percentage. Use the slider to adjust the level and 

select the Set button. In the case when the there are multiple dimmer 

outputs controlled by the same sensor, this value is the dimmer RATIO. 

Constant Lighting Controller

C

M

Y

CM

MY

CY

CMY

K

28

Dialog® Lighting Control System

The Groups screen has three tabs:

1. 

Label
To modify a group name:

 

a) 

Select an output and select its label.

 

b) 

Enter the new preset name and select the OK button.

2. 

Control

You can activate, deactivate, or configure a selected group. The procedures 

differ depending on the CLC setting type, as follows:

Threshold Trigger

 

a) 

Activate or deactivate an output by selecting the 

ACTIVATE

 or   

 

 

DEACTIVATE 

button.  

  An orange rectangle is displayed for activated modes and a blue rectangle 

  for deactivated modes. 

 

b) 

Select the 

LOW LEVEL

 or 

HIGH LEVEL

 button to view the current 

Low  

  Level Set Point

 or 

High Level Set Point

, respectively. Adjust the set   

  points by using the slider and selecting the 

Set

 button. 

 

c) 

Select the 

MODIFY 

button to view or modify sensor parameters, as follows:

    1. 

Triggering Preset 

- display any of the CLC triggering presets 

 

 

    associated with the output.

    2. 

Daylight Sensor

 - select the associated 

link

 to modify the controlling   

    sensor. Next, select the new 

sensor

. 

    3. 

CLC Function

 - select the associated 

link

 to modify the CLC type. Next, 

    select the 

Open Loop

 or 

Closed Loop

 option and select the 

OK

    4. 

High Level Target

 - select the associated 

link

 to modify the high level   

    target, which is the relay output that is turned on when the light levels 

 

    exceed the High Level Set Point. Next, select the 

new output.

 

    5. 

Test Mode

 - select the associated 

link

 to enable or disable the test   

    mode. By default, this option is turned off.  If this option is enabled, there 

    is no delay time between light level readings. 

  Open Loop

a) 

Activate or deactivate a selected dimmer group by selecting the 

ACTIVATE

or 

DEACTIVATE 

button.  

An orange rectangle is displayed for activated modes and a blue rectangle 

for deactivated modes. 

b) 

Select the 

DIMMER

 button to adjust the dimmer out dimming level Set 

Point. This is set as a percentage. Use the slider to adjust the level and 

select the Set button. In the case when the there are multiple dimmer 

outputs controlled by the same sensor, this value is the dimmer RATIO. 

Constant Lighting Controller

C

M

Y

CM

MY

CY

CMY

K

28

Dialog® Lighting Control System

The Groups screen has three tabs:

1. 

Label
To modify a group name:

 

a) 

Select an output and select its label.

 

b) 

Enter the new preset name and select the OK button.

2. 

Control

You can activate, deactivate, or configure a selected group. The procedures 

differ depending on the CLC setting type, as follows:

Threshold Trigger

 

a) 

Activate or deactivate an output by selecting the 

ACTIVATE

 or   

 

 

DEACTIVATE 

button.  

  An orange rectangle is displayed for activated modes and a blue rectangle 

  for deactivated modes. 

 

b) 

Select the 

LOW LEVEL

 or 

HIGH LEVEL

 button to view the current 

Low  

  Level Set Point

 or 

High Level Set Point

, respectively. Adjust the set   

  points by using the slider and selecting the 

Set

 button. 

 

c) 

Select the 

MODIFY 

button to view or modify sensor parameters, as follows:

    1. 

Triggering Preset 

- display any of the CLC triggering presets 

 

 

    associated with the output.

    2. 

Daylight Sensor

 - select the associated 

link

 to modify the controlling   

    sensor. Next, select the new 

sensor

. 

    3. 

CLC Function

 - select the associated 

link

 to modify the CLC type. Next, 

    select the 

Open Loop

 or 

Closed Loop

 option and select the 

OK

    4. 

High Level Target

 - select the associated 

link

 to modify the high level   

    target, which is the relay output that is turned on when the light levels 

 

    exceed the High Level Set Point. Next, select the 

new output.

 

    5. 

Test Mode

 - select the associated 

link

 to enable or disable the test   

    mode. By default, this option is turned off.  If this option is enabled, there 

    is no delay time between light level readings. 

  Open Loop

a) 

Activate or deactivate a selected dimmer group by selecting the 

ACTIVATE

or 

DEACTIVATE 

button.  

An orange rectangle is displayed for activated modes and a blue rectangle 

for deactivated modes. 

b) 

Select the 

DIMMER

 button to adjust the dimmer out dimming level Set 

Point. This is set as a percentage. Use the slider to adjust the level and 

select the Set button. In the case when the there are multiple dimmer 

outputs controlled by the same sensor, this value is the dimmer RATIO. 

Constant Lighting Controller

C

M

Y

CM

MY

CY

CMY

K

28

Dialog® Lighting Control System

The Groups screen has three tabs:

1. 

Label
To modify a group name:

 

a) 

Select an output and select its label.

 

b) 

Enter the new preset name and select the OK button.

2. 

Control

You can activate, deactivate, or configure a selected group. The procedures 

differ depending on the CLC setting type, as follows:

Threshold Trigger

 

a) 

Activate or deactivate an output by selecting the 

ACTIVATE

 or   

 

 

DEACTIVATE 

button.  

  An orange rectangle is displayed for activated modes and a blue rectangle 

  for deactivated modes. 

 

b) 

Select the 

LOW LEVEL

 or 

HIGH LEVEL

 button to view the current 

Low  

  Level Set Point

 or 

High Level Set Point

, respectively. Adjust the set   

  points by using the slider and selecting the 

Set

 button. 

 

c) 

Select the 

MODIFY 

button to view or modify sensor parameters, as follows:

    1. 

Triggering Preset 

- display any of the CLC triggering presets 

 

 

    associated with the output.

    2. 

Daylight Sensor

 - select the associated 

link

 to modify the controlling   

    sensor. Next, select the new 

sensor

. 

    3. 

CLC Function

 - select the associated 

link

 to modify the CLC type. Next, 

    select the 

Open Loop

 or 

Closed Loop

 option and select the 

OK

    4. 

High Level Target

 - select the associated 

link

 to modify the high level   

    target, which is the relay output that is turned on when the light levels 

 

    exceed the High Level Set Point. Next, select the 

new output.

 

    5. 

Test Mode

 - select the associated 

link

 to enable or disable the test   

    mode. By default, this option is turned off.  If this option is enabled, there 

    is no delay time between light level readings. 

  Open Loop

a) 

Activate or deactivate a selected dimmer group by selecting the 

ACTIVATE

or 

DEACTIVATE 

button.  

An orange rectangle is displayed for activated modes and a blue rectangle 

for deactivated modes. 

b) 

Select the 

DIMMER

 button to adjust the dimmer out dimming level Set 

Point. This is set as a percentage. Use the slider to adjust the level and 

select the Set button. In the case when the there are multiple dimmer 

outputs controlled by the same sensor, this value is the dimmer RATIO. 

Constant Lighting Controller

C

M

Y

CM

MY

CY

CMY

K

28

Dialog® Lighting Control System

The Groups screen has three tabs:

1. 

Label
To modify a group name:

 

a) 

Select an output and select its label.

 

b) 

Enter the new preset name and select the OK button.

2. 

Control

You can activate, deactivate, or configure a selected group. The procedures 

differ depending on the CLC setting type, as follows:

Threshold Trigger

 

a) 

Activate or deactivate an output by selecting the 

ACTIVATE

 or   

 

 

DEACTIVATE 

button.  

  An orange rectangle is displayed for activated modes and a blue rectangle 

  for deactivated modes. 

 

b) 

Select the 

LOW LEVEL

 or 

HIGH LEVEL

 button to view the current 

Low  

  Level Set Point

 or 

High Level Set Point

, respectively. Adjust the set   

  points by using the slider and selecting the 

Set

 button. 

 

c) 

Select the 

MODIFY 

button to view or modify sensor parameters, as follows:

    1. 

Triggering Preset 

- display any of the CLC triggering presets 

 

 

    associated with the output.

    2. 

Daylight Sensor

 - select the associated 

link

 to modify the controlling   

    sensor. Next, select the new 

sensor

. 

    3. 

CLC Function

 - select the associated 

link

 to modify the CLC type. Next, 

    select the 

Open Loop

 or 

Closed Loop

 option and select the 

OK

    4. 

High Level Target

 - select the associated 

link

 to modify the high level   

    target, which is the relay output that is turned on when the light levels 

 

    exceed the High Level Set Point. Next, select the 

new output.

 

    5. 

Test Mode

 - select the associated 

link

 to enable or disable the test   

    mode. By default, this option is turned off.  If this option is enabled, there 

    is no delay time between light level readings. 

  Open Loop

a) 

Activate or deactivate a selected dimmer group by selecting the 

ACTIVATE

or 

DEACTIVATE 

button.  

An orange rectangle is displayed for activated modes and a blue rectangle 

for deactivated modes. 

b) 

Select the 

DIMMER

 button to adjust the dimmer out dimming level Set 

Point. This is set as a percentage. Use the slider to adjust the level and 

select the Set button. In the case when the there are multiple dimmer 

outputs controlled by the same sensor, this value is the dimmer RATIO. 

Constant Lighting Controller

C

M

Y

CM

MY

CY

CMY

K

28

Dialog® Lighting Control System

The Groups screen has three tabs:

1. 

Label
To modify a group name:

 

a) 

Select an output and select its label.

 

b) 

Enter the new preset name and select the OK button.

2. 

Control

You can activate, deactivate, or configure a selected group. The procedures 

differ depending on the CLC setting type, as follows:

Threshold Trigger

 

a) 

Activate or deactivate an output by selecting the 

ACTIVATE

 or   

 

 

DEACTIVATE 

button.  

  An orange rectangle is displayed for activated modes and a blue rectangle 

  for deactivated modes. 

 

b) 

Select the 

LOW LEVEL

 or 

HIGH LEVEL

 button to view the current 

Low  

  Level Set Point

 or 

High Level Set Point

, respectively. Adjust the set   

  points by using the slider and selecting the 

Set

 button. 

 

c) 

Select the 

MODIFY 

button to view or modify sensor parameters, as follows:

    1. 

Triggering Preset 

- display any of the CLC triggering presets 

 

 

    associated with the output.

    2. 

Daylight Sensor

 - select the associated 

link

 to modify the controlling   

    sensor. Next, select the new 

sensor

. 

    3. 

CLC Function

 - select the associated 

link

 to modify the CLC type. Next, 

    select the 

Open Loop

 or 

Closed Loop

 option and select the 

OK

    4. 

High Level Target

 - select the associated 

link

 to modify the high level   

    target, which is the relay output that is turned on when the light levels 

 

    exceed the High Level Set Point. Next, select the 

new output.

 

    5. 

Test Mode

 - select the associated 

link

 to enable or disable the test   

    mode. By default, this option is turned off.  If this option is enabled, there 

    is no delay time between light level readings. 

  Open Loop

a) 

Activate or deactivate a selected dimmer group by selecting the 

ACTIVATE

or 

DEACTIVATE 

button.  

An orange rectangle is displayed for activated modes and a blue rectangle 

for deactivated modes. 

b) 

Select the 

DIMMER

 button to adjust the dimmer out dimming level Set 

Point. This is set as a percentage. Use the slider to adjust the level and 

select the Set button. In the case when the there are multiple dimmer 

outputs controlled by the same sensor, this value is the dimmer RATIO. 

Constant Lighting Controller

C

M

Y

CM

MY

CY

CMY

K

Threshold Trigger:

a)

1.

a)

2.

3.

4.

5.

b)

c)

b)

Open Loop:

Summary of Contents for WLC-4150-C












































Reviews:

No comments

Related manuals for WLC-4150-C

DARKSTAR TECHNOLOGIES D340 Manual To Operation preview
D340
Brand: DARKSTAR TECHNOLOGIES Pages: 4
TDW D2000 Maintenance Manuallines preview
D2000
Brand: TDW Pages: 2
Taurus 1170 Assembly And Operating Instructions Manual preview
1170
Brand: Taurus Pages: 25
Vancare G Series Quick Reference Manual preview
G Series
Brand: Vancare Pages: 3
Paitec ES-2000 User Manual preview
ES-2000
Brand: Paitec Pages: 14
Campden instruments 7600 Series Instruction Manual preview
7600 Series
Brand: Campden instruments Pages: 8
Eagle Eye SG-1000 User Manual preview
SG-1000
Brand: Eagle Eye Pages: 21
Labomed Magna User Manual preview
Magna
Brand: Labomed Pages: 67
Ognibene STA Service Manual preview
STA
Brand: Ognibene Pages: 28
Hameg HM303-6 Manual preview
HM303-6
Brand: Hameg Pages: 24
Vaisala HMP Series User Manual preview
HMP Series
Brand: Vaisala Pages: 118
Velp Scientifica ECO 8 Operation Manual preview
ECO 8
Brand: Velp Scientifica Pages: 12
Yamaha D24 Upgrade Manual preview
D24
Brand: Yamaha Pages: 24
J&M Nitro Gro 5010 Assembly Manual preview
Nitro Gro 5010
Brand: J&M Pages: 33
PAT EI65 Operator'S Manual preview
EI65
Brand: PAT Pages: 44
Park Tool TS-2Di Instructions And Parts Diagram preview
TS-2Di
Brand: Park Tool Pages: 4
Qlight S80AR Instruction Manual preview
S80AR
Brand: Qlight Pages: 4
Safavieh Lighting LIT4352A Instructions preview
LIT4352A
Brand: Safavieh Lighting Pages: 2

Brands by name

Popular brands

Load more brands