21
ENGLISH
12
PLAYING CDs
(1) Playing CDs
ON / STANDBY
FUNCTION
2
/ BAND
VOLUME
PERSONAL AUDIO SYSTEM / CD RECEIVER
1
CLEAR
1
2
3
5
4
6
7
8
9
+10
10
TONE/SDB
REPEAT
CALL
PROG /
DIRECT
RANDOM
ENTER
DISPLAY
MENU
SLEEP
FOLDER
TITLE
TIME
POWER
OPEN / CLOSE
STOP
/BAND
PLAY/PAUSE
VOLUME
PRESET
5
1
3
2
2
3
NOTES:
• “No Disc” is displayed when no disc is loaded
or the disc is loaded inside out.
• According to recording quality, some CD-R/RW
cannot be played.
• The all-track/1-track remaining time is not
displayed if the information on the disc cannot
be read properly due to scratches or dirt. In this
case, some time may be required for cueing.
• When the
5
or
1
/
3
button is pressed while in
the standby mode, the power turns on and the
disc loading/unloading operation or the playback
operation is performed.
• Do not use CDs that have the exposed
adhesive or marks remaining from cellophane
tape, rental CD labels, or other sources. Use of
CDs in this condition will result in difficulty in
removing the CD or could cause breakdown.
2
Load a CD in the
disc door.
(See page 12.)
1
Press the button
to turn the power
on.
POWER
(RC-909)
3
Press the
1
/
3
button to start
playback.
PLAY/PAUSE
(RC-909)
(Main unit)
OPEN / CLOSE
5
(RC-909)
(Main unit)
During playback,
press the
2
/BAND
button.
STOP
/BAND
(RC-909)
2
/ BAND
(Main unit)
(2) Stopping playback
ON / STANDBY
FUNCTION
2
/ BAND
VOLUME
PERSONAL AUDIO SYSTEM / CD RECEIVER
1
TONE/SDB
ENTER
DISPLAY
MENU
STOP
/BAND
PLAY/PAUSE
VOLUME
FUNCTION
MUTE
PRESET
+
-
1
1
11
ADJUSTING THE TONE
TONE/SDB
ENTER
DISPLAY
MENU
SLEEP
FOLDER
TITLE
TIME
STOP
/BAND
PLAY/PAUSE
VOLUME
FUNCTION
MUTE
PRESET
+
-
2
1
1
Press the TONE/SDB button to adjust
the tone and display the mode.
Each time you press this
button, the display changes as
follows:
TONE/SDB
2
3
The adjusted value is displayed for
approximately 5 seconds, after which
the display returns to normal.
Treble 0dB
SDB Off
Bass 0dB
Mid 0dB
Press the +/
−
buttons to adjust the
level.
• The level can be adjusted in
the range of
−
10 to 0 to +10
in steps of 2.
• The “TONE” indicator is
displayed when the level is
set at anything other than
0dB.
To adjust the bass, mid-range or
treble
PRESET
+
-
Press the +/
−
buttons to
select “On” or “Off”.
• When set to “On”, the
“SDB” indicator lights.
To adjust the SDB
PRESET
+
-
2
The bass (BASS), mid-range (MID), treble (TREBLE)
super dynamic bass (SDB) can each be adjusted to
achieve the desired tone.
2
The volume of the bass sound is increased
according to the overall volume and the
above BASS adjustment.
ON / STANDBY
(Main unit)
Lit green
About installation
2
About speaker installation
• Set the speakers sufficiently apart from each
other to achieve a suitable stereo effect (sense
of expansion).
• It is recommended that the speakers be placed
at least 7 cm from the D-107. (See the diagram
below.)
The quality of the sound produced from the speakers
depends on the size of the room, the type of room
(Japanese style or western style) and how the
speakers are mounted. Adjust the sound to suit your
tastes.
2
About subwoofer installation
• The set’s sound balance is set assuming the
subwoofer is installed on the floor.
• If the subwoofer is placed against a wall, the
bass sound may seem amplified due to the
sound reflecting off the wall. Adjust the bass
sound (BASS) to suit your tastes.
See “Adjusting the tone” for instructions on
adjusting the bass sound (BASS).
7 cm or greater
On floor
2
About main unit installation
When installing on a desk or table, mount the
included stand and set the unit vertically. (See
page 7.)
The disc may fall out of the disc holder if the unit
is set in any direction other than vertically. (See
page 12.)
