background image

Back to Contents Page

  

 

 AC Adapter Connector  

Dell™ Studio XPS™ 1340 Service Manual 

 

  

Removing the AC Adapter Connector 

 

  

Replacing the AC Adapter Connector 

 

 

 

 

 

 

 

 

 

 

 

Removing the AC Adapter Connector  

 

 

1.

Follow the instructions in 

Before You Begin

.  

 

 

  

2.

Remove the eSATA connector (see 

Removing the eSATA Connector

).  

 

 

  

3.

Remove the screw that secures the AC adapter connector.  
 

 

  

4.

Remove the AC adapter cable from the routing guide.  
 

 

  

5.

Lift the AC adaptor connector and cable out of the computer base.  
 

  

 

Replacing the AC Adapter Connector  

 

 

1.

Place the AC adapter connector in the computer base.  
 

 

  

2.

Replace the screw that secures the AC adapter connector.  
 

 

  

3.

Route the AC adapter cable through the routing guide.  
 

 

 

 

 

 

CAUTION: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. 

 

NOTICE: 

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface 

(such as the back panel) on the computer. 

 

NOTICE: 

Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is 

not covered by your warranty. 

 

NOTICE: 

To help prevent damage to the system board, remove the main battery (see 

Before Working Inside Your Computer

) before working 

inside the computer. 

screw 

AC adaptor connector 

cable routing 

 

 

 

 

 

NOTICE: 

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may 

result in damage to the computer. 

Summary of Contents for Studio XPS 1340








































Reviews: