Dell Studio XPS 1340 Page 19 Service Manual Download

Page: 19 / 39

Back to Contents Page

Hard Drive

Dell™ Studio XPS™ 1340 Service Manual

Removing the Hard Drive

Replacing the Hard Drive

Removing the Hard Drive

Follow the instructions in

Before You Begin

Remove the base cover (see

Removing the Base Cover

Remove the four screws securing the hard drive assembly to the computer base.

Pull the blue pull-tab to disconnect the hard drive assembly from the system board connector.

Lift the hard drive out of the computer base.

Pull the interposer to detach it from the hard drive.

CAUTION:

If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive.

CAUTION:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

NOTICE:

To prevent data loss, turn off your computer (see

Turning Off Your Computer

) before removing the hard drive. Do not remove the hard

drive while the computer is on or in Sleep state.

NOTICE:

Hard drives are extremely fragile. Exercise care when handling the hard drive.

NOTICE:

Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is

not covered by your warranty.

NOTICE:

To help prevent damage to the system board, remove the main battery (see

Before Working Inside Your Computer

) before working

inside the computer.

NOTE:

Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell.

NOTE:

If you are installing a hard drive from a source other than Dell, you need to install an operating system, drivers, and utilities on the new hard

drive (see the

Dell Technology Guide

NOTICE:

When the hard drive is not in the computer, store it in protective antistatic packaging (see "Protecting Against Electrostatic Discharge"

in the safety instructions that shipped with your computer).

blue pull-tab

screws (4)

hard drive assembly

Summary of Contents for Studio XPS 1340








































Search results

Summary of Contents for Studio XPS 1340

Reviews:

Related manuals for Studio XPS 1340

Brands by name

Popular brands

Dell Studio XPS 1340, Service Manual

Search results

Summary of Contents for Studio XPS 1340

Reviews:

Related manuals for Studio XPS 1340

Brands by name

Popular brands