Dell Studio XPS 1340 Page 18 Service Manual Download | Manualshive

Page: 18 / 39

background image

5.

Replace the system board (see

Replacing the System Board

).

6.

Replace the display assembly (see

Replacing the Display Assembly

Back to Contents Page

NOTICE:

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may

result in damage to the computer.

«
...
16
17
18
19
20
...
»

Summary of Contents for Studio XPS 1340








































Reviews:

No comments

Related manuals for Studio XPS 1340

Brand: Ohio Scientific Pages: 43

Brand: Ace Pages: 17

Brand: Igel Pages: 2

Brand: PROAIM Pages: 3

eBOX625-842-FL Series

Brand: AXIOMTEK Pages: 60

Brand: C&T Solution Pages: 108

Brand: Compaq Pages: 2

Brand: Compaq Pages: 222

Brand: Sun Microsystems Pages: 45

Brand: MSI Pages: 85

Brand: Wacom Pages: 340

INSPIRON Inspiron 5000

Brand: Dell Pages: 132

Brand: Vivo Pages: 5

DA-682A-DPP Series

Brand: Moxa Technologies Pages: 7

Brand: Shuttle Pages: 34

Brand: A.K.Microsystems Pages: 47

Brand: Xerox Pages: 73

Brand: Balt Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands