Dell Studio XPS 1340 Page 10 Service Manual Download

Page: 10 / 39

Back to Contents Page

Processor

Dell™ Studio XPS™ 1340 Service Manual

Removing the Processor

Installing the Processor

Removing the Processor

Follow the instructions in

Before You Begin

Remove the base cover (see

Removing the Base Cover

Remove the rear caps (see

Removing the Rear Caps

Remove the central processor heat sink (see

Removing the Central Processor Heat Sink

To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop.

The ZIF-socket cam screw secures the processor to the system board. Take note of the arrow on the ZIF-socket cam screw.

Use a processor extraction tool to remove the processor.

CAUTION:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface

(such as a connector on the back of the computer).

NOTICE:

To prevent intermittent contact between the ZIF-socket cam screw and the processor when removing or replacing the processor, press

to apply slight pressure to the center of the processor while turning the cam screw.

NOTICE:

To avoid damage to the processor, hold the screwdriver so that it is perpendicular to the processor when turning the cam screw.

NOTICE:

Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is

not covered by your warranty.

NOTICE:

To help prevent damage to the system board, remove the main battery (see

Before Working Inside Your Computer

) before working

inside the computer.

NOTICE:

When removing the processor, pull it straight up. Be careful not to bend the pins on the processor.

processor

pin-1 corner of processor

ZIF socket

ZIF-socket cam screw

Summary of Contents for Studio XPS 1340








































Search results

Summary of Contents for Studio XPS 1340

Reviews:

Related manuals for Studio XPS 1340

Brands by name

Popular brands

Dell Studio XPS 1340, Service Manual

Search results

Summary of Contents for Studio XPS 1340

Reviews:

Related manuals for Studio XPS 1340

Brands by name

Popular brands