Dell Studio XPS 1340 Page 23 Service Manual Download | Manualshive

Page: 23 / 39

background image

Replacing the Keyboard

1.

Replace the keyboard on the palm rest.

2.

Align the keyboard shield over the screw holes on the palm rest.

3.

Replace the ten screws that secure the keyboard and the shield to the palm rest.

4.

Connect the backlit keyboard cable (availability varies according to region) to the connector.

5.

Connect the multimedia board cable and power board cable to their connectors.

6.

Connect the dual multimedia board/power board cable to the connector.

7.

Replace the palm rest (see

Replacing the Palm Rest

).

Back to Contents Page

3 keyboard shield

4 screws (10)

5 keyboard

6 dual multimedia board/power

board cable connector

7 backlit keyboard cable connector

(availability varies according to region)

NOTICE:

The keycaps on the keyboard are fragile, easily dislodged, and time- consuming to replace. Be careful when removing and handling the

keyboard.

«
...
21
22
23
24
25
...
»

Summary of Contents for Studio XPS 1340








































Reviews:

No comments

Related manuals for Studio XPS 1340

Brand: Knoll Pages: 2

Brand: Avalue Technology Pages: 78

FieldGo PCATX-R9

Brand: BSi Pages: 40

Brand: Advantech Pages: 17

Brand: GARANT Pages: 60

Brand: Vivo Pages: 3

Brand: Dell Pages: 121

Brand: Dell Pages: 57

Brand: Dell Pages: 80

Brand: Dell Pages: 112

Brand: Dell Pages: 78

Brand: Dell Pages: 57

Brand: Dell Pages: 144

OptiPlex 5480 All-in-One

Brand: Dell Pages: 102

Brand: Dell Pages: 16

Brand: Dell Pages: 158

Brand: Dell Pages: 22

Brand: Dell Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands