Dell Studio XPS 1340 Page 2 Service Manual Download

Page: 2 / 39

Back to Contents Page

Base Cover

Dell™ Studio XPS™ 1340 Service Manual

Removing the Base Cover

Replacing the Base Cover

Removing the Base Cover

Ensure that the computer is turned off.

Remove the battery (see

Before Working Inside Your Computer

Loosen the ten captive screws on the base cover and lift the cover off the computer.

Replacing the Base Cover

Replace the base cover.

Tighten the ten captive screws on the base cover.

Slide the battery into the battery bay until it clicks into place.

Back to Contents Page

CAUTION:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION:

Before performing these procedures, turn off the computer, disconnect the AC adapter from the electrical outlet and the computer,

disconnect the modem from the wall connector and the computer, and remove any other external cables from the computer.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface

(such as a connector on the back of the computer).

NOTICE:

Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is

not covered by your warranty.

NOTICE:

To help prevent damage to the system board, remove the main battery (see

Before Working Inside Your Computer

) before working

inside the computer.

CAUTION:

Do not touch the processor heat sink. Processor components should be removed only by trained support personnel.

base cover

captive screws (10)

Summary of Contents for Studio XPS 1340








































Search results

Summary of Contents for Studio XPS 1340

Reviews:

Related manuals for Studio XPS 1340

Brands by name

Popular brands

Dell Studio XPS 1340, Service Manual

Search results

Summary of Contents for Studio XPS 1340

Reviews:

Related manuals for Studio XPS 1340

Brands by name

Popular brands