Dell Studio XPS 1340 Page 15 Service Manual Download

Page: 15 / 39

Back to Contents Page

Display Assembly

Dell™ Studio XPS™ 1340 Service Manual

Removing the Display Assembly

Replacing the Display Assembly

Removing the Display Assembly

Follow the instructions in

Before You Begin

Remove the palm rest (see

Removing the Palm Rest

Remove the optical drive (see

Removing the Optical Drive

Make note of the Mini-Card cable routing and carefully dislodge the Mini-Card antenna cables from their routing guides.

Pull the Mini-Card cables out through the system board so that they are clear of the computer base.

Make note of the display cable, power light cable, and camera cable routing.

Remove the display cable grounding screw that secures the display ground cable to the system board.

CAUTION:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface

(such as a connector on the back of the computer).

NOTICE:

Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is

not covered by your warranty.

NOTICE:

To help prevent damage to the system board, remove the main battery (see

Before Working Inside Your Computer

) before working

inside the computer.

NOTICE:

To avoid damage to the display, you must not disassemble your Edge-to- Edge display assembly in the field.

Summary of Contents for Studio XPS 1340








































Search results

Summary of Contents for Studio XPS 1340

Reviews:

Related manuals for Studio XPS 1340

Brands by name

Popular brands

Dell Studio XPS 1340, Service Manual

Search results

Summary of Contents for Studio XPS 1340

Reviews:

Related manuals for Studio XPS 1340

Brands by name

Popular brands