Dell Studio XPS 1340 Page 32 Service Manual Download | Manualshive

Page: 32 / 39

background image

6.

Detach the interposer from the optical drive.

Replacing the Optical Drive

1.

Attach the interposer to the optical drive.

2.

Place the optical drive in the computer base.

3.

Replace the two screws that secure the optical drive to the system board.

4.

Turn the computer over and replace the screw that secures the optical drive to the computer base.

5.

Replace the palm rest (see

Replacing the Palm Rest

).

Back to Contents Page

«
...
30
31
32
33
34
...
»

Summary of Contents for Studio XPS 1340








































Reviews:

No comments

Related manuals for Studio XPS 1340

Brand: DIVERSIFIED WOODCRAFTS Pages: 18

Brand: Seneca Pages: 8

Brand: Zotac Pages: 20

Brand: Vivo Pages: 12

MultiSync X463UN

Brand: NEC Pages: 6

MultiSync X551S

Brand: NEC Pages: 9

MultiSync X463UN

Brand: NEC Pages: 44

MultiSync X551UN

Brand: NEC Pages: 9

POWERMATE CT 815 - RELEASE NOTES

Brand: NEC Pages: 165

Brand: NEC Pages: 110

Brand: NEC Pages: 116

PM-ECO-900 - PowerMate Eco - 256 MB RAM

Brand: NEC Pages: 28

Brand: NEC Pages: 181

MultiSync X463UN

Brand: NEC Pages: 2

Brand: NEC Pages: 195

Brand: NEC Pages: 255

POWERMATE ES 5250 - S

Brand: NEC Pages: 276

Brand: NEC Pages: 184

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands