Dell Studio XPS 1340 Service Manual Download

Page: 35 / 39

Back to Contents Page

AC Adapter Connector

Dell™ Studio XPS™ 1340 Service Manual

Removing the AC Adapter Connector

Replacing the AC Adapter Connector

Removing the AC Adapter Connector

Follow the instructions in

Before You Begin

Remove the eSATA connector (see

Removing the eSATA Connector

Remove the screw that secures the AC adapter connector.

Remove the AC adapter cable from the routing guide.

Lift the AC adaptor connector and cable out of the computer base.

Replacing the AC Adapter Connector

Place the AC adapter connector in the computer base.

Replace the screw that secures the AC adapter connector.

Route the AC adapter cable through the routing guide.

CAUTION:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface

(such as the back panel) on the computer.

NOTICE:

Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is

not covered by your warranty.

NOTICE:

To help prevent damage to the system board, remove the main battery (see

Before Working Inside Your Computer

) before working

inside the computer.

screw

AC adaptor connector

cable routing

NOTICE:

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may

result in damage to the computer.

Summary of Contents for Studio XPS 1340








































Search results

Summary of Contents for Studio XPS 1340

Reviews:

Related manuals for Studio XPS 1340

Brands by name

Popular brands

Dell Studio XPS 1340, Service Manual

Search results

Summary of Contents for Studio XPS 1340

Reviews:

Related manuals for Studio XPS 1340

Brands by name

Popular brands