Dell Aurora R6 Service Manual Download Page 84

Page: 84 / 164

Removing the processor fan and

heat-sink assembly

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before working inside your computer

. After working inside your

computer, follow the instructions in

After working inside your

computer

. For more safety best practices, see the Regulatory

Compliance home page at

www.dell.com/regulatory_compliance

WARNING: The heat sink may become hot during normal operation.
Allow sufficient time for the heat sink to cool before you touch it.

CAUTION: For maximum cooling of the processor, do not touch the
heat transfer areas on the heat sink. The oils in your skin can reduce
the heat transfer capability of the thermal grease.

Prerequisites

Remove the

left-side cover

Follow the procedure from step 1 to step 4 in "

Removing the power-supply

unit

Procedure

Disconnect the processor-fan cable from the system board.

In a non-adjacent sequence, loosen the captive screws that secure the
processor fan and heat-sink assembly to the system board.

Summary of Contents for Aurora R6





































































































































































Search results

Summary of Contents for Aurora R6

Reviews:

Related manuals for Aurora R6

Brands by name

Popular brands

Dell Aurora R6, Service Manual

Search results

Summary of Contents for Aurora R6

Reviews:

Related manuals for Aurora R6

Brands by name

Popular brands