Dell Aurora R6 Service Manual Download Page 131

Page: 131 / 164

Table 5. System setup options—Advanced menu

Advanced

Advanced BIOS Features

Intel SpeedStep

Allows you to enable or disable Intel
Speedstep Technology. Default:
Enabled.

NOTE: If enabled, the processor
clock speed and core voltage
are adjusted dynamically based
on the processor load.

Virtualization

Allows you to enable or disable Intel
Virtualization Technology feature for
the processor.

VT for Direct I/O

Allows you to enable or disable Intel
Virtualization Technology feature for
the Direct I/O.

SATA Operation

Allows you to configure the operating
mode of the integrated SATA hard
drive controller.

Intel Ready Mode Technology

Allows you to enable or disable the
Intel Ready Mode Technology.

Intel Software Guard Extensions

Allows you to enable or disable Intel
Software Guard Extensions.

BIOS Recovery from Hard Drive

Allows you to enable or disable BIOS
Recovery from hard drive.

USB Configuration

Front USB Ports

Allows you to enable or disable the
front USB ports.

Rear USB Ports

Allows you to enable or disable the
rear USB ports.

Power Options

Numlock Key

Allows you to set the status of the Num
Lock key during boot to On or Off.

131

Summary of Contents for Aurora R6





































































































































































Search results

Summary of Contents for Aurora R6

Reviews:

Related manuals for Aurora R6

Brands by name

Popular brands

Dell Aurora R6, Service Manual

Search results

Summary of Contents for Aurora R6

Reviews:

Related manuals for Aurora R6

Brands by name

Popular brands