manualshive.com logo in svg

Dell Aurora R6, Service Manual, Page: 83 / 164

Share
Download
Dell Aurora R6 Service Manual Download Page 83

Replacing the graphics card

WARNING: Before working inside your computer, read the safety 
information that shipped with your computer and follow the steps in 

Before working inside your computer

. After working inside your 

computer, follow the instructions in 

After working inside your 

computer

. For more safety best practices, see the Regulatory 

Compliance home page at 

www.dell.com/regulatory_compliance

.

 

Procedure

1 

Align the graphics card with the slot on the system board.

2 

Place the card into the slot and press down firmly until the graphics card 
snaps into place.

3 

Connect the power cables to the graphics card.

4 

Slide the tab on the graphics-card bracket into the slot on the chassis and 
snap it into place.

Post-requisites

1 

Follow the procedure from step 10 to step 11 in "

Replacing the power-supply 

unit

".

2 

Replace the 

left-side cover

.

83

Summary of Contents for Aurora R6





































































































































































Reviews:

No comments