DeDietrich AGC 10/15 Installation And Service Manual Download Page 76 | Manualshive

Page: 76 / 132

DeDietrich AGC 10/15 Installation And Service Manual Download Page 76

5.4.4.

Basic setting for the gas/air ratio

If the gas/air ratio is out of adjustment, the gas valve unit has a basic

setting. To do this, proceed as follows:
1. Switch off the boiler electrical power supply.
2. Close the gas valve on the boiler.
3. Remove the air inlet flue on the venturi.
4. Unscrew the top connection on the gas valve unit.
5. Disconnect the connector located under the fan.
6. Release the 2 clips holding the fan/mixing elbow unit in place on

the heat exchanger.

7. Completely remove the fan/mixing elbow unit.

¼

For steps 3 to 7 inclusive, see chapter: "Checking the burner

and cleaning the heat exchanger", page 102

8. Turn the setting screw

A

on the gas valve unit to modify the

position of the restrictor.

9. Turn the setting screw

B

on the gas valve unit anticlockwise until

it matches the front panel.

10.Turn the setting screw

B

on the gas valve unit by 6 turns clockwise.

11.Follow the procedure in reverse to re-assemble all of the

components.

5.5

Checks and adjustments after commissioning

5.5.1.

Displaying the parameters in extended
mode

The display mode on the control panel is set as standard in such a

way as only to show the conventional parameters. It is possible to

switch to extended mode by proceeding as follows:
1. Access the installer level: Press key

-

for around 5 seconds.

2. Select the menu

#SYSTEM

.

4

Turn the rotary button to scroll through the menus or

modify a value.

4

Press the rotary button to access the menu selected

or confirm a value modification.

¼

For a detailed explanation of menu browsing, refer

to the chapter: "Browsing in the menus", page 66

3. Set parameter

INSTALLATION

to

EXTENDED

.

Installer level - Menu #SYSTEM
Parameter

Adjustment range Description

Factory setting Customer setting

INSTALLATION CLASSIC

Displays the parameters of a conventional

installation

CLASSIC

EXTENDED

Displays all parameters

B

T001985-B

A

8

9

10

1

1

2

2

r

c

STD

(

'

t

v

0

2

4

6

8

10

12

14

16

18

22

24

20

p

b

AUTO

x c

r

j

M

g

m

SUNDAY 11:45

5"

TEMP.: 68°

C002235-F-04

5. Commissioning

AGC 10/15 - AGC 15 - AGC 25 - AGC 35

74

20/01/2012 - 300026081-001-B

«
...
74
75
76
77
78
...
»

Summary of Contents for AGC 10/15





































































































































Reviews:

No comments