DeDietrich AGC 10/15 Installation And Service Manual Download Page 72

Page: 72 / 132

3. The first time the boiler is powered up, the

LANGUAGE

menu is

displayed. Select the desired language by turning the rotary

button.

4. To confirm, press the rotary button.
The boiler will begin an automatic venting-programme (which lasts

approx. 3 minutes) and will do this every time the power supply is

isolated.

Error during the start-up procedure:

No information is shown on the display:

Check the mains supply voltage

Check the fuses

Check the connection of the power cable to the connector X1

on the PCU PCB

If there is a problem, the error is displayed on the screen.

See chapter: "Messages (Code type Bxx or Mxx)", page

103

5.4

Gas settings

5.4.1.

Adapting to another gas type

WARNING

Only a qualified engineer may carry out the following

operations.

The boiler is preset in the factory to operate on natural gas H (G20).

For operation on another group of gases, carry out the following

operations:

Set the fan speed using the parameters

MIN.VENT.

MAX.VENT.BOIL

MAX.VENT.DHW

and

START SP.

See chapter: "Professional settings", page 84

Set the air/gas ratio.

"Setting the air/gas ratio (Full load)", page 71

"Setting the air/gas ratio (Part load)", page 72

Affix the label which indicates for which type of gas the boiler is

fitted and set.

Français - Deutsch - English -
Italiano - Espanol - Nederlands
- Pycck - Polski - Türk -

bar

STD

(

x c

LANGUE

FRANCAIS

C002286-C

L000182-A

XXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXX
XXXXXXXXXX

XXXXXXXXXXXX
XXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXX
XXXXXXXX

5. Commissioning

AGC 10/15 - AGC 15 - AGC 25 - AGC 35

20/01/2012 - 300026081-001-B

Summary of Contents for AGC 10/15





































































































































Search results

Summary of Contents for AGC 10/15

Reviews:

DeDietrich AGC 10/15, Installation And Service Manual, Page: 72 / 132

Search results

Summary of Contents for AGC 10/15

Reviews: