DeDietrich AGC 10/15 Installation And Service Manual Download Page 20

Page: 20 / 132

4 Installation

4.1

Regulations governing installation

WARNING

Installation of the appliance must be done by a qualified

engineer in accordance with prevailing local and national

regulations.

4.2

Package list

4.2.1.

Standard delivery

The delivery includes:

The boiler, fitted with a connection cable

Outside sensor

Installation and Service Manual

User Guide

4.2.2.

Accessories

Various options are available depending on the configuration of the

installation.

Boiler options
Description

package

Condensates neutralisation station

DU13

Condensates neutralisation station without lift pump BP52
Flue gas safety thermostat

JA38

adapter 80/125

HR38

3-way internal valve kit

JA6

External circuit kit

JA7

Direct elbow

JA43

Propane conversion kit AGC 15

JA39

Propane conversion kit AGC 25

JA40

Propane conversion kit AGC 35

JA41

4. Installation

AGC 10/15 - AGC 15 - AGC 25 - AGC 35

20/01/2012 - 300026081-001-B

Summary of Contents for AGC 10/15





































































































































Search results

Summary of Contents for AGC 10/15

Reviews:

DeDietrich AGC 10/15, Installation And Service Manual, Page: 20 / 132

Search results

Summary of Contents for AGC 10/15

Reviews: