manualshive.com logo in svg

DeDietrich AGC 10/15, Installation And Service Manual, Page: 106 / 132

Share
Download
DeDietrich AGC 10/15 Installation And Service Manual Download Page 106

Code

Messages

Description

Checking / solution

B07

BL.DT OUTL RET.

Maximum difference

between the flow and return

temperature exceeded

The water flow in the installation is insufficient

4

Check the circulation (direction, pump, valves)

4

Check the water pressure

4

Check the cleanliness of the heat exchanger

Sensor error

4

Check that the sensors are operating correctly

4

Check whether the boiler sensor has been correctly fitted

B08

BL.RL OPEN

The 

RL

 inlet on the PCU

PCB terminal block is open

Parameter error

4

Set the type of generator again in the menu

#CONFIGURATION

 (Refer to the original rating plate)

Bad connection

4

Check the wiring

B09

BL.INV. L/N

Set the type of generator again in the menu 

#CONFIGURATION

 (Refer to the original rating

plate )

B10
B11

BL.BL INPUT OPEN

The 

BL

 inlet on the PCU

PCB terminal block is open

The contact connected to the 

BL

 inlet is open

4

Check the contact on the 

BL

 inlet

Parameter error

4

Check the parameter 

IN.BL

Bad connection

4

Check the wiring

B13

BL. PCU COM

Communication error with

the SCU PCB

Bad connection

4

Check the wiring

SCU PCB not installed in the boiler

4

Install an SCU PCB

B14

BL.WATER MIS.

The water pressure is lower

than 0,8 bar

Not enough water in the circuit

4

Top up the installation with water

B15

BL.GAS PRESS

Gas pressure too low

Incorrect setting of the  gas pressure switch on the SCU PCB

4

Check that the gas valve is fully opened

4

Checking the gas supply pressure

4

Check whether the  gas pressure control system has been

correctly fitted

4

Replace the  gas pressure control system if need be

B16

BL.BAD SU

The SU PCB is not

recognised

Wrong SU PCB for this boiler

4

Replace the SU PCB

B17

BL.PCU ERROR

The parameters saved on

the PCU PCB are impaired

Parameter error on the PCU PCB

4

Replace the PCU PCB

B18

BL.BAD PSU

The PSU PCB is not

recognised

Wrong PSU PCB for this boiler

4

Replace the PSU PCB

B19

BL.NO CONFIG

The boiler has not been

configured

The PSU PCB has been changed

4

Set the type of generator again in the menu

#CONFIGURATION

 (Refer to the original rating plate)

B21

BL. COM SU

Communication error

between the PCU and SU

PCBs

Bad connection

4

Check that the SU PCB has been correctly put in place on

the PCU PCB

4

Replace the SU PCB

8. Troubleshooting

AGC 10/15 - AGC 15 - AGC 25 - AGC 35

104

20/01/2012  - 300026081-001-B

Summary of Contents for AGC 10/15





































































































































Reviews:

No comments