Danfoss VLT Micro Drive FC 51 Series Design Manual Download Page 48

Page: 48 / 98

6 How to Install

6.1 Before Starting

6.1.1 Checklist

When unpacking the frequency converter, make sure that
the unit is undamaged and complete. Check that the
packaging contains the following:

•

VLT

Micro Drive FC 51

•

Quick Guide

Optional: LCP and/or de-coupling plate.

Illustration 6.1 Content of box

6.2 Side-by-Side Installation

The frequency converter can be mounted side-by-side for
IP 20 rating units and requires 100 mm clearance above
and below for cooling. Regarding surroundings in general,
see

7 Programming

Illustration 6.2 Side-by-side Installation

6.3 Before Commencing Repair Work

Disconnect FC 51 from mains (and external DC
supply, if present.)

Wait for 4 min (M1, M2 and M3) and 15 min (M4
and M5) for discharge of the DC-link. See

Table 2.1

Disconnect DC bus terminals and brake terminals
(if present).

Remove motor cable.

How to Install

VLT

Micro Drive FC 51 Design Guide

MG02K202 - VLT

is a registered Danfoss trademark

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for VLT Micro Drive FC 51 Series



































































































Search results

Summary of Contents for VLT Micro Drive FC 51 Series

Reviews:

Related manuals for VLT Micro Drive FC 51 Series

Brands by name

Popular brands

Danfoss VLT Micro Drive FC 51 Series, Design Manual

Search results

Summary of Contents for VLT Micro Drive FC 51 Series

Reviews:

Related manuals for VLT Micro Drive FC 51 Series

Brands by name

Popular brands