background image

4 Parameter Setup

4.1 Introduction to Parameter Setup

The parameters included in this Operating Guide are extracts from the drive-specific programming guides. Refer to these
Programming Guides for full parameter descriptions.

4.2 5-** Digital In/Out

4.2.1 Parameter Group 5-1* Digital Inputs

The digital inputs are used for selecting various functions in the drive. Refer to 

table 7

 to see which functions can be assigned to digital

inputs.

Functions in group 1 have higher priority than the functions in group 2.

Group 1

Reset, coast stop, reset, and coast stop, quick stop, DC brake, stop, and the [Off] key.

Group 2

Start, latched start, reversing, start reversing, jog, and freeze output.

Table 7: Digital Input Functions

Digital input function

Select

Terminal

No operation

[0]

All, terminal 32, 33

Reset

[1]

All

Coast inverse

[2]

All, terminal 27

Coast and reset inverse

[3]

All

Quick stop inverse

[4]

All

DC brake inverse

[5]

All

Stop inverse

[6]

All

Start

[8]

All, terminal 18

Latched start

[9]

All

Reversing

[10]

All, terminal 19

Start reversing

[11]

All

Enable start forward

[12]

All

Enable start reverse

[13]

All

Jog

[14]

All, terminal 29

Preset reference on

[15]

All

Preset ref bit 0

[16]

All

Preset ref bit 1

[17]

All

Preset ref bit 2

[18]

All

Freeze reference

[19]

All

Freeze output

[20]

All

Parameter Setup

Operating Guide  | VLT® Extended Relay Card MCB 113

AQ322553864968en-000101 / 130R0353| 15

Danfoss A/S © 2020.01

Summary of Contents for MCB 113























































Reviews: