13-01 Start Event
Option:
Function:
[5]
Torque limit
Torque limit
[5] The torque limit, set in
or
4-17 Torque Limit Generator Mode
, has
been exceeded.
[6]
Current limit
Current limit
[6] The motor current limit,
set in
, has been
exceeded.
[7]
Out of current
range
Out of current range
[7] The motor current
is outside the range set in
[8]
Below I low
Below I low
[8] The motor current is lower
[9]
Above I high
Above I high
[9] The motor current is
higher than set in
[10]
Out of speed
range
Out of speed range
[10] The speed is
outside the range set in
and
.
[11]
Below speed low
Below speed low
[11] The output speed is
lower than the setting in
[12]
Above speed
high
Above speed high
[12] The output speed is
higher than the setting in
[13]
Out of feedb.
range
Out of feedb. Range
[13] The feedback is
outside the range set in
and
[14]
Below feedb. low
Below feedb. Low
[14] The feedback is
below the limit set in
[15]
Above feedb.
high
Above feedb. High
[15] The feedback is
above the limit set in
[16]
Thermal warning
Thermal warning
[16]:the thermal warning
turns on when the temperature exceeds
the limit in the motor, the adjustable
frequency drive, the brake resistor or the
thermistor.
[17]
Mains out of
range
AC line voltage out of range [17] The AC
line voltage is outside the specified
voltage range.
[18]
Reverse
Reversing
[18] The output is high when
the adjustable frequency drive is running
counter-clockwise (the logical product of
the status bits “running” AND “reverse”).
[19]
Warning
Warning
[19] A warning is active.
13-01 Start Event
Option:
Function:
[20]
Alarm (trip)
Alarm (trip)
[20] A (trip) alarm is active.
[21]
Alarm (trip lock)
Alarm (trip lock)
[21] A (Trip lock) alarm is
active.
[22]
Comparator 0
Comparator 0
[22] Use the result of
comparator 0.
[23]
Comparator 1
Comparator 1
[23] Use the result of
comparator 1.
[24]
Comparator 2
Comparator 2
[24] Use the result of
comparator 2.
[25]
Comparator 3
Comparator 3
[25] Use the result of
comparator 3.
[26]
Logic rule 0
Logic rule 0
[26] Use the result of logic rule
0.
[27]
Logic rule 1
Logic rule 1
[27] Use the result of logic rule
1.
[28]
Logic rule 2
Logic rule 2
[28] Use the result of logic rule
2.
[29]
Logic rule 3
Logic rule 3
[29] Use the result of logic rule
3.
[33]
Digital input DI18
Digital input DI18
[33] Use the result of
digital input 18.
[34]
Digital input DI19
Digital input DI19
[34] Use the result of
digital input 19.
[35]
Digital input DI27
Digital input DI27
[35] Use the result of
digital input 27.
[36]
Digital input DI29
Digital input DI27
[35] Use the result of
digital input 29.
[37]
Digital input DI32
Digital input DI32
[37] Use the result of
digital input 32.
[38]
Digital input DI33
Digital input DI33
[38] Use the result of
digital input 33.
[39]
Start command
Start command
[39] A start command is
issued.
[40]
Drive stopped
Drive stopped
[40] A stop command (Jog,
Stop, Qstop, Coast) is issued – and not
from the SLC itself.
[41]
Reset Trip
Reset Trip
[41] A reset is issued
[42]
Auto-reset Trip
Auto-reset Trip
[42]: an auto reset is
performed.
[43]
OK key
OK key
[43] The Ok key is pressed.
[44]
Reset key
Reset key
[44] The reset key is pressed.
[45]
Left key
Left key
[45] The left key is pressed.
[46]
Right key
Right key
[46] The right key is pressed.
Parameter Descriptions
FC 300 Programming Guide
MG.33.MA.22 - VLT
®
is a registered Danfoss trademark
3-107
3
3