Danfoss D9h, Operating Manual

Page: 166 / 206

FC 302 N450 N500
Line reactor overtemperature trip [°C (°F)] 150 (302) 150 (302)
dU/dt filter overtemperature trip [°C (°F)] 150 (302) 150 (302)
Sine-wave filter overtemperature trip [°C (°F)] 150 (302) 150 (302)
1
Typical power loss is at normal conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions.) These
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to dimension-
ing of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control card power
consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-efficiency-direc-
tive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each
add only 4 W.
2
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy efficien-
cy class, see the Ambient Conditions section. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
3 See also Input Power Option Losses section.
4
If using an output filter, the output frequency is limited further. See 10.3.1 Motor Output (U, V, W) .
10.1.2 Electrical Data, 525–690 V AC
Table 105: Electrical Data, Mains Supply 3x525–690 V AC
FC 302 N90K N110 N132 N160
High/normal overload
High overload=150% or 160% torque for a
duration of 60 s. Normal overload=110% tor-
que for a duration of 60 s.
HO NO HO NO HO NO HO NO
Typical shaft output at 550 V [kW] 75 90 90 110 110 132 132 160
Typical shaft output at 575 V [hp] 100 125 125 150 150 200 200 250
Typical shaft output at 690 V [kW] 90 110 110 132 132 160 160 200
Enclosure size D9h D9h D9h D10h
Output current (3-phase)
Continuous (at 550 V) [A] 113 137 137 162 162 201 201 253
Intermittent (60 s overload) (at 550 V) [A] 170 151 206 178 243 221 301 278
Continuous (at 575/690 V) [A] 108 131 131 155 155 192 192 242
Intermittent (60 s overload) (at 575/690 V) [A] 162 144 197 171 233 211 288 266
Continuous kVA (at 550 V) [kVA] 103 125 125 147 147 183 183 230
Continuous kVA (at 575 V) [kVA] 108 131 131 154 154 191 191 241
Continuous kVA (at 690 V) [kVA] 129 157 157 185 185 230 229 289
Maximum input current
Continuous (at 525 V) [A] 109 132 132 156 156 193 193 244
Continuous (at 575/690 V) [A] 104 126 126 149 149 185 185 233
Maximum number and size of cables per phase
- Mains [mm
2
(AWG)] 2x95 (2x3/0 mcm) 2x95 (2x3/0 mcm) 2x95 (2x3/0 mcm) 2x185 (2x350 mcm)
AQ262139143212en-000301 / 130R0879 166 | Danfoss A/S © 2021.10
Specifications
VLT® AutomationDrive FC 302
Operating Guide