English
24
LED indications
h
:OFF
k
:ON
l
:BLINK
MODE
HWL:
k
C/H SELECTOR
L.N.O.P DEMAND
indications on
remote
controller
(*1)
Functions of push-button
IND
MASTER SLAVE
H1P
H2P
H3P
H4P
H5P
H6P
H7P
h
h
k
h
h
h
h
h
k
k
h
h
h
h
h
l
h
h
h
h
k
h
l
h
h
h
k
k
LED indications to connect the refrigerant tank.
l
l
l
h
k
h
h
h
l
h
h
k
h
h
LED indications to [open] the valve of refrigerant tank.
l
l
l
h
k
h
k
h
l
h
h
k
h
k
LED indications as re-charging amount of refrig-
erant is not sufficient.
l
l
l
h
l
h
h
h
l
h
h
k
k
h
h
h
k
h
h
h
h
h
l
l
h
h
h
k
h
k
k
h
h
h
h
(*1) : Please refer to [Remote controller indica-
tions at check operation] to confirm the
details of each indication.
(*2) : If outside panels are not closed, it may not
be able to operate normally when outdoor
temperature is high, etc.
(*3) : Remote controller does not indicate the
procedures. Make sure to check the LED
indications upon operation.
(*4) : Recode the amount of refrigerant re-charge
on the [Safety precaution] label.
WARNING
ELECTRIC SHOCK WARNING
• Do not move away from the outdoor unit if outside panel is not closed during a test
operation.
• In case you need to move away from the outdoor unit, follow either one of the below
directions.
1.
Replace with other installation worker.
2.
Push the “RETURN” button (BS3) to cancel the test operation.
(In this case, close all the outside panel, and close also the valve if any cylinder is
connected.)
A
B
C
C
C
C
C
A
B
(P2)
B
D
(P8)
D
(PA)
C
(*3)
• If the system stops and a indoor remote controller
indicates any defect, repair the defect part according
to. [Remote controller displays malfunction code.]
Test operate again after the repair.
• To test operate again, press the “RETURN button”
(BS3) to turn the LED back to “normal” indications
as procedure (1).
In this case, either refrigerant tank became empty, or the
valve of the refrigerant tank is not open.
• If the refrigerant tank is empty, replace the tank, then
press the “TEST” button (BS4) for longer than 5 sec. to
re-start the system.
• If the valve of the refrigerant tank is not open, press the
“TEST” button (BS4) for longer than 5 sec. to re-start
the system.
Then open the valve of the refrigerant tank by following
the procedure (3) 2.
• If the system stops and a indoor remote controller
indicates any defect, repair the defect part according
to. [Remote controller displays malfunction code.]
Test operate again after the repair.
• To check operate again, press the “RETURN” button
(BS3) to turn the LED back to “normal” indications
as procedure (1).
If the “TEST” button (BS4) is not
pressed within 3 min. after the
indication to open the valve, it goes
back to procedure (3) 1 and stops
the system again.
BS1
MODE
BS2
SET
BS3
RETURN
BS4
TEST
BS5
RESET
Press to reset the address when
changing the wiring, or indoor units are
added.
Use for a check operation.
• Press to confirm the settings,
• To cancel test operation,
• To go back to procedure (1) after repair of defect
part. (cancellation of error code)
Press to select setting items.
• Press to change setting modes,
• Press to go back to procedure (1), when missing the procedures.
(
(
01_EN_3P226891-14T.fm Page 24 Tuesday, September 30, 2014 7:48 PM
