manualshive.com logo in svg

Daikin EHS157034, Operating Instructions Manual

Share
Download
Daikin EHS157034 Operating Instructions Manual Download Page 57

In order to ensure that the fault has not been caused by 
incorrect setting, set all the parameters back to the 
factory settings before possible replacement of compo-
nents (see chapter 3.6.12).

If you are unable to determine the cause of failure 
yourself, Daikinplease consult a service technician.

Have the significant equipment data to hand 

(see fig. 7-4 for the procedure):

– Type and manufacturer number of the Daikin 

Altherma EHS(X/H)s (see heat pump identifica-
tion plate).

– Software versions (see fig. 7-4) of:

a: Control unit RoCon B1 [Sw Nr B1/U1]

b: Circuit board RoCon BM1 [Sw Nr Controller]

c: RTX-AL4 circuit board [Sw Nr RTX RT]

– On optional RoCon system components:

EHS157034 [Sw Nr B1/U1]

EHS157068 [Sw Nr mixing valve]

Info

Overview

Water Pressure

T-HS

Sw Nr B1/U1

Sw Nr RTX RT

Sw Nr Controller

Info

Sw Nr B1/U1

Sw Nr Controller

Sw Nr RTX RT

Info

Sw Nr B1/U1

Sw Nr mixing valve

Sw Nr mixing valve

Fig. 7-4

Software information of the controller components

7 

x

 Errors, malfunctions and messages

Daikin RoCon HP 
Daikin Controller
008.1420844_13 – 02/2016

Operating instructions

57

7.2

Emergency operation

In the case of incorrect setting in the electronic control system or 
malfunction of the 3-way diverter valves, emergency heating op-
eration can be maintained by activating the 

special "Manual Op-

eration" function

 on the control unit (see chapter 3.5.1 and the 

supplementary instructions in the installation and mainte-
nance manual

 of the Daikin Altherma EHS(X/H).

7.3

Malfunctions and fault codes

See Daikin Altherma EHS(X/H) installation and maintenance 
manual; section: "Faults, malfunctions, messages".

Summary of Contents for EHS157034

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands