manualshive.com logo in svg

Daikin EHS157034, Operating Instructions Manual

Share
Download
Daikin EHS157034 Operating Instructions Manual Download Page 51

6 

x

 Parameter settings

Daikin RoCon HP 
Daikin Controller
008.1420844_13 – 02/2016

Operating instructions

51

6.10 Rotary switch setting: Info 

Parameter

Description

Access

Setting range

Min / Max

Factory 

setting

Increment

BE

HF

Overview

Display of different current operating data (see section 3.4.1).

S

S

-

-

-

Water Pressure

The current water pressure is displayed in bar.

S

S

0 - 4 bar

-

0.1 bar

T-HS

The current temperature (TVBH) of the heat generator is displayed in °C.

S

S

0 - 100 °C

-

1 °C

T-HS Setpoint

The current Inflow target temperature of the heat generator is displayed in °C 

(see section 3.6.4).

S

S

0 - 90 °C

-

0.1 °C

T-Outside

The average external temperature is displayed °C.

S

S

-39 to +50 °C

0.1 °C

T-DHW

The current temperature of the hot water storage tank is displayed in °C. If there is no hot 
water function activated, "- - -" is displayed.

S

S

0 - 100 °C

-

0.1 °C

T-DHW Setpoint

The current target hot water temperature is displayed °C. If there is no hot water function ac-
tivated, "- - -" is displayed. The current set value is here always the maximum value of all 
relevant demands for this hot water circuit.

S

S

10 - 70°C

-

0.1 °C

T-Return

The current return flow temperature of the heat generator is displayed in °C. If there is no 
relevant sensor connected to the heat generator, "- - -" is displayed.

S

S

0 - 100 °C

-

0.1 °C

Flow Rate

The filtered value of the current volume flow in litres per hour is displayed.

S

S

0 - 5100 l/h

-

l/h

T-HC

The inflow temperature in the direct heating circuit is displayed in °C.

S

S

0 - 100 °C

-

0.1 °C

T-HC Setpoint

The set temperature of the flow in the direct heating circuit is displayed in °C.

S

S

0 - 90 °C

-

0.1 °C

Status HS pump

The current status of the internal heat circulation pump in the Daikin Altherma EHS(X/H) is 
displayed.

S

S

Off
On

-

-

Runtime Compres-
sor

The running time of the refrigerant compressor is displayed in h.

S

S

-

-

h

Runtime Pump

The running time of the internal heating circulation pump is displayed in h.

S

S

-

-

h

Mixer Position

The current position of the 3UV DHW 3-way switch valve is displayed.
0%: Position A (room heating)
100%: Position B (domestic hot water generation)

S

S

0 - 100 %

-

1 %

Qboh

The amount of heat in the additional heat generator for hot water generation is displayed in 
kWh.

S

S

-

-

kWh

Qchhp

The amount of heat in the additional heat generator for heating mode is displayed in kWh.

S

S

-

-

kWh

Qsc

The quantity of heat in the heat pump for cooling is displayed in kWh.

S

S

-

-

kWh

Qch

The quantity of heat in the heat pump for heating is displayed in kWh.

S

S

-

-

kWh

QWP

The total amount of heat in the heat pump is displayed in kWh.

S

S

-

-

kWh

Qdhw

The quantity of heat for hot water generation is displayed in kWh.

S

S

-

-

kWh

HS type

The heat generator type Daikin Altherma EHS(X/H) detected is displayed.

S

S

-

-

-

Sw Nr B1/U1

The software and version of the control unit RoCon B1 B1 / 

 of the room station 

EHS157034is displayed.

S

S

-

-

-

Sw Nr Controller

The software number and the version of the RoCon BM1 circuit board are displayed.

S

S

-

-

-

Sw Nr RTX RT

The software number and the version of the RTX-AL4 circuit board are displayed.

S

S

-

-

-

Tab. 6-12 Parameter in rotary switch setting "Info"

6.11 Exit button: Sonderfunktion

Depress the exit button for at least 5 secs. for access.

Parameter

Description

Access

Setting range

Min / Max

Factory 

setting

Increment

BE

HF

Manual Operation

The direct heating circuit and the target hot water temperature are controlled according to 
the temperature set in this parameter (see section 3.5.1).

E

E

20 - 80 °C

50 °C

1 °C

FA failure

Display of a current heat pump malfunction in the Daikin Altherma EHS(X/H). 

If "----" is displayed there is no fault (see chapter 7).

E

E

-

-

-

Protocol

Display of protocol (error and information messages). Here we display the saved messages 
of the Daikin Altherma EHS(X/H) and the connected RoCon system components with date 
and code as a menu entry in each case. By selecting an entry to using the rotary switch, all 
other corresponding information is displayed concerning the selected message:
- Date and time of the message
- Code number (Information for the heating technician)
- Device type from which the message comes
- Device ID for the RoCon unit where the message originates

E

E

-

-

-

Delete message

By setting this parameter to "On" and briefly pressing the rotary switch, all entries in the re-
port, including the faults from connected RoCon system components, are deleted.

E

E

Off
On

Off

-

RoCon B1/U1 Reset Resets all parameter settings to factory setting. Required for software updates or changes 

to the RoCon system (see chapter 4.2). Complete reconfiguration subsequently required.

N

E

Off
On

Off

-

Summary of Contents for EHS157034

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands