manualshive.com logo in svg

Daikin EHS157034, Operating Instructions Manual

Share
Download
Daikin EHS157034 Operating Instructions Manual Download Page 5

1 

x

 Safety

Daikin RoCon HP 
Daikin Controller
008.1420844_13 – 02/2016

Operating instructions

5

1.2.2 Validity

Some information in this manual has limited va-
lidity. The validity is highlighted by a symbol.

Only valid for Daikin Altherma EHS(X/H) 
with cooling function
Valid/available only if a room station 
(EHS157034) is connected
Valid/available only if a mixer module 
(EHS157068) is connected

1.2.3 Handling instructions

●

Handling instructions are shown as a list. 
Actions of which the sequential order must be 
maintained are numbered.

Results of actions are identified with an 
arrow.

1.2.4 Display readouts of the RoCon-

Controller

Entry into a setting procedure
Exit from a setting procedure

Certain screen displays or menu points may 
differ from those shown in these instructions due 
to country or equipment variations in the Daikin 
Altherma EHS(X/H) or the status of the user 
logged onto the Controller.

1.3 Avoiding danger

The Daikin Altherma EHS(X/H) is state-of-the-
art and is built to meet all recognised technical 
requirements. However, improper use may result 
in serious physical injuries or death, as well as 
property damage. 
To avoid danger, only operate the Daikin 
Altherma EHS(X/H):
– as stipulated and in perfect condition,
– with an awareness of safety and the hazards 

involved.

This assumes knowledge and use of the con-
tents of this manual, of the relevant accident pre-
vention regulations as well as the recognised 
safety-related and occupational health rules.

WARNING!

1.4 Proper use

The RoCon HP may be used only in Daikin 
Altherma EHS(X/H) heat pumps that have been 
approved for Daikin the regulating system-
RoCon. The Daikin RoCon HP may only op-
erated only according to the indications in this 
manual.
Any other use outside the intended use is con-
sidered as improper. The operator alone shall 
bear responsibility for any resulting damage.
For any work on the equipment, which extends 
above and beyond the operation of the regu-
lating system, you must observe the details pro-
vided in the supplementary documents, particu-
larly with regard to safety instructions.

This equipment must only be used by 

children

 aged 8 and above and by 

persons with restricted physical, sensory 
or mental capabilities or with a lack of ex-
perience and knowledge, if they are 
under supervision or if they have been 
instructed in the safe use of the 
equipment and understand the dangers 
arising therefrom. 

Children

 must not 

play with the equipment. Cleaning or 

user maintenance

 must not be carried 

out by 

children

 without supervision.

Summary of Contents for EHS157034

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands