manualshive.com logo in svg

D-Link DWS-4026, User Manual

Share
Download
D-Link DWS-4026 User Manual Download Page 263

Software User Manual

 D-Link Unified Access System

12/10/09

Document

34CSFP6XXUWS-SWUM100-D7

Managing LLDP

Page  263

M

ANAGING

 LLDP

The IEEE 802.1AB defined standard, Link Layer Discovery Protocol (LLDP), allows stations residing on an 802 LAN to
advertise major capabilities and physical descriptions. This information is viewed by a network manager to identify system
topology and detect bad configurations on the LAN.

LLDP is a one-way protocol; there are no request/response sequences. Information is advertised by stations implementing
the transmit function, and is received and processed by stations implementing the receive function. The transmit and receive
functions can be enabled/disabled separately per port. By default, both transmit and receive are disabled on all ports. The
application is responsible for starting each transmit and receive state machine appropriately, based on the configured status
and operational state of the port.

D-Link allows LLDP to have multiple LLDP neighbors per interface. The number of such neighbors is limited by the memory
constraints. A product-specific constant defines the maximum number of neighbors supported by the switch. There is no
restriction on the number of neighbors supported on a per LLDP port. If all the remote entries on the switch are filled up, then
the new neighbors are ignored. In case of multiple VOIP devices on a single interface, the 802.1ab component sends the
Voice VLAN configuration to all the VoIP devices.

The LLDP folder contains links to the following page:

•

“Global Configuration” 

•

“Interface Configuration” 

•

“Interface Summary” 

•

“Statistics” 

•

“Local Device Information” 

•

“Local Device Summary” 

•

“Remote Device Information” 

•

“Remote Device Summary” 

•

“LLDP-MED” 

Summary of Contents for DWS-4026

































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands