Crystal Vision Indigo 2 CoolFlow User Manual Download Page 9 | Manualshive

Page: 9 / 45

background image

Crystal Vision

Installation

Indigo 2 CoolFlow User Manual R1.3

8

20/06/2012

2.3 Connector pinout

Remote Control / GPI Connections

Each frame slot has six connections that are brought out to one or more of the four high
density D-Type connectors on the rear of the frame labelled Remote 1 to 4. These
connections are referred to as lines 'a' to 'f'. The functions assigned to them are dependent on
the module inserted in each slot, but a typical use is as a GPI line. Refer to the
documentation supplied with each Crystal Vision module to determine the actual functions
assigned.

Remote 1 and Remote 3 connections (26 way high density D-Type socket)

Pin number

Remote 1 - function

Remote 3 - function

1

+5.3V +/- 10% dc out

+5.3V +/- 10% dc out

2

Frame GND

Frame GND

3

Slot 9 GPI ‘a’

Slot 11 GPI ‘a’

4

Slot 6 GPI ‘a’

Slot 8 GPI ‘a’

5

Slot 5 GPI ‘a’

Slot 7 GPI ‘a’

6

Slot 5 GPI ‘b’

Slot 7 GPI ‘b’

7

Slot 2 GPI ‘a’

Slot 4 GPI ‘a’

8

Slot 1 GPI ‘a’

Slot 3 GPI ‘a’

9

Slot 1 GPI ‘b’

Slot 3 GPI ‘b’

10

Slot 10 GPI ‘a’

Slot 12 GPI ‘a’

11

Slot 10 GPI ‘b’

Slot 12 GPI ‘b’

12

Slot 9 GPI ‘b’

Slot 11 GPI ‘b’

13

Slot 6 GPI ‘c’

Slot 8 GPI ‘c’

14

Slot 6 GPI ‘b’

Slot 8 GPI ‘b’

15

Slot 5 GPI ‘c’

Slot 7 GPI ‘c’

16

Slot 2 GPI ‘b’

Slot 4 GPI ‘b’

17

Slot 2 GPI ‘c’

Slot 4 GPI ‘c’

18

Slot 1 GPI ‘c’

Slot 3 GPI ‘c’

19

Slot 10 GPI ‘c’

Slot 12 GPI ‘c’

20

Slot 10 GPI ‘d’

Slot 12 GPI ‘d’

21

Slot 9 GPI ‘d’

Slot 11 GPI ‘d’

22

Slot 9 GPI ‘c’

Slot 11 GPI ‘c’

23

Slot 6 GPI ‘d’

Slot 8 GPI ‘d’

24

Slot 5 GPI ‘d’

Slot 7 GPI ‘d’

25

Slot 2 GPI ‘d’

Slot 4 GPI ‘d’

26

Slot 1 GPI ‘d’

Slot 3 GPI ‘d’

Note:

The total current available from the 5.3V dc outputs is limited to approximately
1.5Amps.
To maintain EMC compliance only good quality screened cable assemblies should be
used.

«
...
7
8
9
10
11
...
»

Summary of Contents for Indigo 2 CoolFlow














































Reviews:

No comments

Related manuals for Indigo 2 CoolFlow

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 5

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 21

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 2

WJMPU955 - PROCESSING UNIT - TMU

Brand: Panasonic Pages: 62

Brand: Hama Pages: 4

Brand: Salto Pages: 2

Brand: Vivotek Pages: 136

Brand: Vonets Pages: 8

Brand: DAQ system Pages: 41

Brand: DAQ system Pages: 19

Brand: MiLAN Pages: 1

PacketShaper PS-S200

Brand: Symantec Pages: 2

Brand: Teac Pages: 20

cMT-FHDX Series

Brand: Maple Systems Pages: 2

Brand: NETGEAR Pages: 2

ER3-100 (5K02-55)

Brand: 8e6 Technologies Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands