background image

Crystal Vision 

 

Installation 

Indigo 2 CoolFlow User Manual R1.3

 14

  

20/06/2012 

 
Switch three is for debug purposes and should normally be left in the up position. 

Default IP address (Indigo 2SE only) 

Switch four in the down position sets the active front panel to the default IP address of 
10.0.0.201. This default address is necessary to be able to change the IP address during 
installation.  

PSU Configuration 

PSU configuration only applies to the 2U and 4U frames where it is possible to have 
multiple power supplies fitted into a single frame. Should a power supply not be fitted in 
either the upper or lower slots of the 2U frame or the upper or lower slots of the lower 
section of the 4U frame, the position of the two-position slide switch must be set 
accordingly.  

If both power supplies are fitted the slide switch is set to position two. If the switch is set to 
one and there are two power supplies fitted, the LOWER PSU LED will flash from GREEN 
to OFF every two to three seconds to warn that the switch is incorrectly set. Should only a 
single power supply be fitted with the switch set to position two, a power supply fault will 
be registered. 

2.5  Controlling two frames from one panel 

A single active or remote control panel may control modules in up to two frames. This 
constitutes a frame pair where one frame is set to its upper slot address range and the other 
to its lower address range. Only one panel in a frame pair needs to be non-passive. 

If a remote REMIND panel is used the controlled frames need only have passive panels, if 
both frames are controlled from one frame that frame should have an active panel and the 
other a passive panel.  

Note: 

If a frame pair has been established solely for Statesman control, one of the frames can 
have a Statesman panel and the other a passive panel. 

 

The two frames can be up to 10m apart depending on cable type and ambient electrical 
noise.  

 

Slot number range 

 

The position of the two-position slide switch labelled Upper/Lower on the top edge of the 
front panel PCB must be placed in the Lower position for one frame and in the Upper 

Summary of Contents for Indigo 2 CoolFlow














































Reviews: