Cronyx FMUX/SAT Installation And Operation Manual Download

Page: 4 / 44

FMUX/SAT Multiplexer

Contents

Section 1. Introduction ....................................................6

1.1. Purpose .....................................................................................................

1.2. Features ....................................................................................................

1.3. Order Code ...............................................................................................

1.4. Connection Diagram ................................................................................

1.5. Specifications ........................................................................................... 9

E1 Ports .................................................................................................... 9

Link Port .................................................................................................. 9

Console Port ............................................................................................. 9

SNMP Management Port ....................................................................... 1

Emergency Alarm Port........................................................................... 1

Diagnostic Modes .................................................................................. 1

Dimensions and Weight

......................................................................... 1

Power Supply ......................................................................................... 1

Operating Conditions ............................................................................. 1

Section 2. Installation....................................................11

2.1. Installation Space Requirements .............................................................11

2.2. Delivered Items .......................................................................................11

2.3. Cable Connections ..................................................................................11

Power Supply Connector ....................................................................... 12

Grounding .............................................................................................. 12

E1 Port Connectors ................................................................................ 12

Link Port Connector (V.35, RS-530, RS-449) ....................................... 13

Cable Diagrams for Connections to Link Port ...................................... 14

V.35 Cable for Connection to DCE ............................................... 14

V.35 Cable for Connection to DTE ................................................ 14

RS-530 Cable for Connection to DСE .......................................... 15

RS-530 Cable for Connection to DTE ........................................... 15

RS-449 Cable for Connection to DCE .......................................... 1

RS-449 Cable for Connection to DTE ........................................... 1

SNMP Port Connector ........................................................................... 1

Console Port Connector ......................................................................... 1

Emergency Alarm Connector ................................................................. 1

Summary of Contents for FMUX/SAT













































Search results

Summary of Contents for FMUX/SAT

Reviews:

Related manuals for FMUX/SAT

Brands by name

Popular brands

Cronyx FMUX/SAT, Installation And Operation Manual

Search results

Summary of Contents for FMUX/SAT

Reviews:

Related manuals for FMUX/SAT

Brands by name

Popular brands