Cronyx FMUX/SAT Page 9 Installation And Operation Manual Download | Manualshive

Page: 9 / 44

background image

© 2006 Cronyx

Section 1. Introduction

1.5. Specifications

E1 Ports

Nominal bit rate ............................................................. 2,048 kbit/s

Encoding

........................................................................ HDB3

Frame structure .............................................................. Transparent G.703 stream

transmission in both framed

(G.704), and unframed mode

Error control ................................................................... Code violations
Link impedance .............................................................. 120 Ohm balanced (twisted

pair)

Receiver signal level ...................................................... 0 to -12 dB
Jitter attenuation ............................................................. In the transmit path
Overvoltage protection ................................................... TVS
Overcurrent protection ................................................... Fuse
Connector ...................................................................... RJ-48 (female, 8 pin)

Link Port

Interface type ................................................................. Multistandard (V.35, RS-530,

RS-449); in the codirectional

mode

Clock frequency ............................................................. 8.448, 6.336, 4.224 or

2.112 MHz ± 30 ppm

Modem signals ............................................................... TXD, ETC, RXD, RXC, CD,

DSR, CTS, RTS

Connector ....................................................................... HDB44 (female)

Console Port

Interface type ................................................................. RS-232 DCE
Data transmission protocol ............................................ Asynchronous, 9600 bit/s, 8

bits/character, 1 stop bit, no

parity

Modem signals ............................................................... DTR, DSR, CTS, RTS, CD
Connector ....................................................................... DB-9 (female)

«
...
7
8
9
10
11
...
»

Summary of Contents for FMUX/SAT













































Reviews:

No comments

Related manuals for FMUX/SAT

Brand: Chauvin Arnox Pages: 40

SDI-TD-MUX-4 Flashlink

Brand: Network Electronics Pages: 22

Brand: CableWorld Pages: 7

Brand: CABAC Pages: 9

Brand: Keithley Pages: 75

Brand: Sperry instrument Pages: 6

Brand: Performance Tool Pages: 2

Brand: Barco Pages: 56

FD9R6004 Series

Brand: RFS Pages: 2

Brand: Mastech Pages: 22

Brand: Tenma Pages: 35

Brand: Raisecom Pages: 26

Brand: UNI-T Pages: 52

Brand: UNI-T Pages: 70

BROADway System 770-0125-AB

Brand: Carrier Access Pages: 96

Brand: Maxwell Pages: 24

Brand: Delton Pages: 11

Brand: APPA Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands