Cronyx FMUX/SAT Installation And Operation Manual Download

Page: 40 / 44

FMUX/SAT Multiplexer

4.9. "Login to remote device" Command

Login to remote device

" command gives ability to connect to the menu of the remote

multiplexer. An example of remote menu is given below. To disconnect from remote

menu, enter ^X (Ctrl-X).

Remote login...
(Press ^X to exit)

Cronyx FMUX / 4E1-SAT-SNMP revision A, 28/04/2006

Mode: Normal; Sensor=Open
Link: 8448 kbps, Ok, Cable cross V.35

DTR, RTS, ETC, DSR, CTS, CD, RXC

1. Link statistics
2. E1 port statistics
3. Event counters
4. Loop...
5. Configure...
0. Reset

Remote (^X to exit): _

In the remote login mode, it is possible to view device modes, port state, and local and

remote error statistics. It is also allowed to set device modes and loops on E1 ports.

4.10. "Reset" Command

Reset

" command causes multiplexer to reload. After this, the modes stored in non-vola-

tile memory (NVRAM) are set.

Summary of Contents for FMUX/SAT













































Search results

Summary of Contents for FMUX/SAT

Reviews:

Related manuals for FMUX/SAT

Brands by name

Popular brands

Cronyx FMUX/SAT, Installation And Operation Manual

Search results

Summary of Contents for FMUX/SAT

Reviews:

Related manuals for FMUX/SAT

Brands by name

Popular brands