CPI T02KO, Installation & Operation Manual

Page: 42 / 122

KA BAND OUTDOOR TWT AMPLIFIER
3-10
AMP
SYSTEM
LCL
M&C
RESET
MENU
FAULT
MENU
ENTER
SETTINGS
METER LOG
TIME
VERSION
AMPLIFIER SELECT
ENTER
ENTER
ENTER
L R
D
D
ENTER
ENTER
L R
D
D
ENTER
ENTER
MANUAL RF OUT: NNN W
ALC RF OUT: NNN W
REFL RF FAULT: NN W
ATTENUATION: NN.N dB
LOW RF ALARM: NNN W
LOW RF FAULT
HIGH RF ALARM’
HIGH RF FAULT
: NNN W
: NNN W
: NNN W
HLX U/V FLT: NN.NN kV
HLX O/I FLT: XX mA
HLX O/V FLT: NN.NNkV
HLX V/STB FLT: N.NNkV
RELAY 1: N
RELAY 2: N
AUTO LOG TIME: NNN.N M
RESET METERLOG?: NO
LIN GAIN: NNN
LIN PHASE: NNN
LIN AMPL: NNN
UNIT ADDRESS: NNN
UNIT ADDRESS: NNN
SYSTEM ID: N
RST TO DFLTS?: NO
D
ENTER
SYSTEM ID: N
RESET TO DFLTS?: NO
RESET TO DFLTS?: N
LIN GAIN: NNN
LIN PHASE: NNN
LIN AMPL: NNN
UNIT ADDRESS: NNN
SYSTEM AMP NO L SINGLE AMP W/ LIN SYSTEM AMP W/ LIN SINGLE AMP NO LIN
METERS
ENTER
U
D
RF OUT: NNN W
HELIX V: NN.NN kV
REFLECTED RF: NNN W
HELIX I:NN mA
CABINET TEMP: NNN C
FAN CONTROL: N.N V
TUBE TEMP: NNN C
ATTENUATION: NN dB
ENTER
METER LOG: 0000
HH:MM:SS MM/DD/YYYY
STATE ENTER
METER LOG: NNNN
(CYCLE THRU LOG
ENTRIES)
U
D
U
D
MORE DATA
LINES
U
D
ENTER
MORE DATA
LINES
ENTER
U
D
TIME: HH:MM:SS MM/DD/YYYY
STANDBY TIME: DDD:HH:MM:SS
UNIT ON TIME: DDD:HH:MM:SS
TRANSMIT TIME: DDD:HH:MM:SS
HEATER TIME DELAY: MM:SS
BOOT: XX.XX.XX
MAIN: XX.XX.XX
MENU
Press MENU key
until “P” appears
on left hand side,
then select
L R
U
D
ENTER
UNITS
RF OUTPUT UNITS: WATT/dBm
U
D
ENTER
BUZZER
U
D
DISPLAY
ENTER
MUTE ALARM: YES/NO
MUTE KEYPAD: YES/NO
DISPLAY BRIGHTNESS: NN%
SCREEN SAVER: YES/NO
L R
ENTER ENTER
ENTER
ENTER
L R
ENTER
U
D
ENTER
IP CONFIG
IP ADDRESS: NNN.NNN.NNN.NNN
IP MASK: NNN.NNN.NNN.NNN
IP GATEWAY: NNN.NNN.NNN.NNN
L R
U
D
TO SELECT 3 DIGIT GROUP
TO ADJUST 3 DIGIT GROUP
SELECT
SELECT
ADJUST
ADJUST
ENTER
CIF PORT
ENTER
L R SELECT
U
D
M&C SERIAL PORT BAUD RATE: NNNN
AMPLIFIER ADDRESS RESCAN: YES/NO
ADJUST
VERSION
BOOT VERSION: NN.NN.NN
MAIN VERSION: NN.NN.NN
PANEL
SELECT
AMPLIFIER SELECT
ENTER
SET TIME
U
D
L R
U
D
SELECT
ADJUST
L R
U
D
ONCE THE DESIRED WINDOW IS REACHED, PRESS
TO HIGHLIGHT THE SELECT ITEM TO BE CHANGED.
NEXT, PRESS TO MODIFY THE SETTING.
AFTER THE DESIRED SETTING IS REACHED PRESS
TO ACTIVATE THE SELECTION.
ENTER
t
MENU FUNCTION KEY TREE
FIGURE B-1
Figure 3-6-a. Remote Control Unit Menu Tree
(Refer to Appendix E for the 11x 17 copy)
INSTALLATION AND OPERATION MANUAL