manualshive.com logo in svg

Cooper Lighting WaveLinx Lite, User And Programming Manual

Share
Download
Cooper Lighting WaveLinx Lite User And Programming Manual Download Page 9

User Manual: WaveLinx Lite (1.5) 

www.cooperlighting.com 

9 

    

 

Outdoor Fixture High/Low Mount Sensor Reference Sheet 

Outdoor Fixture High/Low Mount Sensor 

 

 

 
Features 

•

 

Integrated photocell for closed 

loop daylighting 

•

 

Integrated Passive Infrared (PIR) 

motion sensor 

•

 

Bluetooth 4.2 Low Energy 

transmitter 

 

Typical Applications 

Parking garage, deck, and associated 

pathways 
 

Models: 

WOB

: Low mount: 7-15ft (2.1-4.5m) 

WOF

: High mount: 15-40ft (4.5-12.2m) 

Available option on many Cooper 

Lighting luminaires. 
 

Device Type in Mobile App: 

Highbay Sensor 
 

 
The WaveLinx Lite Outdoor Fixture High/Low Mount Sensor uses a simple tool-less twist lock 

method to connect to a Cooper Lighting fixture with WaveLinx compatible 4-pin Zhaga Book 18 

socket. The sensor has an IP66 rating for outdoor site and indoor environments. 
 

Out-of-the-Box Operation 

•

 

Once power is applied, the attached fixture operates via the daylight and motion sensors. 

•

 

ON at dusk / OFF at dawn via daylight sensor. 

•

 

If fixture is ON at dusk, the occupancy sensor determines the light level. 

•

 

The occupancy is set for High sensitivity. 

•

 

If occupied, the fixture will go to 100%. 

•

 

The fixture will dim to 50% within 7.5 minutes when the space is unoccupied. 

•

 

LED flashes green (in sensor window) for 100ms once every 3 seconds when motion is 

detected. 

 

Provisioned Device Default Behavior 

Once provisioned in the WaveLinx Lite Mobile App, the device operates via the daylight and 

motion sensors. 

•

 

ON at dusk / OFF at dawn via daylight sensor. 

•

 

If the fixture is ON at dusk, the area’s occupancy sensor set

1

 determines the light level. 

•

 

Each occupancy sensor in the set is set for High sensitivity. 

•

 

If occupied, the fixtures of the occupancy set will go to 100%. 

•

 

The occupancy set default hold time is 20 minutes. The fixture will dim to 50% after 10 

minutes when the space is unoccupied and will dim to 0% after an additional 10 

minutes if the space remains unoccupied. 

•

 

LED flashes white (in sensor window) for 100ms once every 3 seconds when motion is 

detected. 

1

 

Note

: This assumes that the device’s assigned zone is assigned to an occupancy set and the occupancy 

set is still at default settings. 

 

LED Behavior 

The LED is located beneath the sensor lens. 

LED conditions 

Meaning 

Flashes green for 100ms, once 

every 3 seconds 

Device is unprovisioned and is detecting motion. 

Flashes white for 100ms, once 

every 3 seconds 

Device is provisioned and is detecting motion 

Flashes white for 10ms every 

250ms (fast blink) 

The daylight sensor has exceeded 150% of the calibrated light 

level for 30 minutes

2

 

LED is OFF 

Device is not detecting motion. If motion is occurring, ensure 

device is powered and that the LED has not been disabled 

through the mobile app.

3

 

2

 

Note

: the LED will stop flashing if the light level drops but stays between 50% and 100% of the calibrated 

light level for 10 minutes OR if the light level falls below 50% of the calibrated light level for 30 seconds. 

3

 

Note

: LED may be difficult to see on high mount fixtures or in very bright areas. 

 

Identification Mode Behavior 

When placed in ‘Blink to Identify’ mode, the fixture will turn ON for 1 second, turn OFF for 1 

second and repeats this cycle for 15 seconds. 
 
 
 

Summary of Contents for WaveLinx Lite















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands