manualshive.com logo in svg

Cooper Lighting WaveLinx Lite, User And Programming Manual, Page: 29 / 78

Share
Download
Cooper Lighting WaveLinx Lite User And Programming Manual Download Page 29

User Manual: WaveLinx Lite (1.5) 

www.cooperlighting.com 

29 

    

 

Modify Default Behavior After Provisioning 

Once an area has been defined, the default behavior can be modified if different operation is expected. This section discusses how to:  

•

 

Modify areas 

•

 

Modify zones  

•

 

Modify devices 

•

 

Modify occupancy sets 

•

 

Modify wallstations 

•

 

Modify scene light levels 

•

 

Calibrate daylight sets 

Modify Areas 

Once created, areas can be renamed or deleted. This section discusses how to perform these functions. 

Rename an Area 

An area can be renamed at any time. This process does not require connection to the internet or a connection to the WaveLinx Lite 

device/network. 
To rename an area: 
1: Open the WaveLinx Lite Mobile Application. 
2: In the site list, select a site. 
3: In the area list or in an area’s screen, select the pencil icon ‘ ’. 
4: Change the area name, and then tap ‘Update’. 
 

 

 

 

Select the site 

Select the edit 

icon 

Update name 

with changes 

Tap ‘Update’ 

Summary of Contents for WaveLinx Lite















































































Reviews:

No comments