manualshive.com logo in svg

Cooper Lighting WaveLinx Lite, User And Programming Manual

Share
Download
Cooper Lighting WaveLinx Lite User And Programming Manual Download Page 17

User Manual: WaveLinx Lite (1.5) 

www.cooperlighting.com 

17 

    

 

Mobile Application Logout 

 
Once logged in to the mobile application, it is not necessary to log out. If needed, the logout function can be accessed from the main menu. 

WARNING: If an App logout is processed, an internet connection will be required to log back in. 

To log out of the mobile application: 
1: Tap the menu button ‘ ’. 
2: Select ‘Sync & Logout’. 
3: The app will start the automatic site sync process. Once the sync completes, the app will logout and return to the login screen. 

 

Note

: Due to the need for the application to sync the site data to the cloud for storage, in order to logout, the mobile device MUST have an internet 

connection to sync site data to the cloud portal during the logout process. If there is no internet connection, logout will be prevented, and the following 

message will be displayed. 
 

 

 

 

Tap the menu 

button 

Select ‘Sync & 

Logout’ 

The sites will load 

and then sync to the 

cloud portal 

Ready for the next 

login command 

Summary of Contents for WaveLinx Lite















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands