manualshive.com logo in svg

Cooper Lighting WaveLinx Lite, User And Programming Manual

Share
Download
Cooper Lighting WaveLinx Lite User And Programming Manual Download Page 14

User Manual: WaveLinx Lite (1.5) 

14 

www.cooperlighting.com 

 

 

Step 2: Register for WaveLinx Lite Mobile Application Access 

Registration is required before using the WaveLinx Lite Mobile Application. Once registered, the user will login to the mobile application using 

the registered email address.  

Note

: The WaveLinx Lite Mobile Application requires a unique email address that is not currently used for other registered WaveLinx Mobile 

Applications. 

 
To register for a WaveLinx Lite account: 
1: Ensure that the mobile device has internet access and then launch the WaveLinx Lite Mobile Application from the app icon. 
2 When the application opens the first time, make sure to grant permission to allow access to location and media files to ensure that the app 

functions properly. 
3: When prompted to login, select the option to register. 

 

 

 

Select ‘Register’ 

Summary of Contents for WaveLinx Lite















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands