Cooper Lighting WaveLinx Lite User And Programming Manual Download Page 13

Page: 13 / 78

User Manual: WaveLinx Lite (1.5)

www.cooperlighting.com

Logging in to the WaveLinx Lite Mobile Application

The WaveLinx Lite Mobile Application is used to provision and organize WaveLinx Lite devices. The mobile application requires user account

registration. During registration, a cloud portal will be established for the user account where the site programming will be stored for backup

purposes. Once the registered account is used to login, the mobile application will remain logged in and will not require an external internet

connection for programming functions as long as the user does not log out of the application. Once an internet connection is available, the site

data can be backed up (synced) to the cloud.
There are some important rules regarding WaveLinx Lite Mobile Application use:

•

Once registered, the WaveLinx Lite Mobile Application can be used to provision any WaveLinx Lite site.

•

Only

one mobile device

should be used per user account.

Note

: If more than one mobile device is used (not recommended), displayed settings may be out of sync and will require manual co-ordination of settings

between the different mobile devices to ensure that settings displayed are accurate and the correct device is used for the backup.

•

Only

one user account

is allowed to setup a site or control the lighting.

•

If the person setting up the site will not administer the site programming once initial programming is complete, the site can be transferred to

a new administrator once the site is backed up to the cloud.

Step 1: Download and install the WaveLinx Lite Mobile Application

The WaveLinx Lite Mobile Application is supported on mobile

devices running iOS 11+ or Android™8+ operating systems.

Download the latest version of the WaveLinx Lite Mobile Application

on the App Store® or get it on Google Play™. Install the mobile app

on a smartphone or tablet.

Once installed, the application icon will be displayed on the mobile

device. If unable to locate the icon, search the installed applications

for ‘WLC’ to locate the app.

IMPORTANT:

Before the WaveLinx Lite Mobile Application can be used on site, the user account must be registered,

the user account must be logged in, and the site must be created. These processes require an internet connection.

Summary of Contents for WaveLinx Lite















































































Search results

Summary of Contents for WaveLinx Lite

Reviews:

Brands by name

Popular brands

Cooper Lighting WaveLinx Lite, User And Programming Manual

Search results

Summary of Contents for WaveLinx Lite

Reviews:

Brands by name

Popular brands