manualshive.com logo in svg

Cooper Lighting WaveLinx Lite, User And Programming Manual

Share
Download
Cooper Lighting WaveLinx Lite User And Programming Manual Download Page 55

User Manual: WaveLinx Lite (1.5) 

www.cooperlighting.com 

55 

    

 

Test Daylight Sensor Operation 

The daylight sensor response can be tested by placing the sensor into test mode. During test mode, the daylight fade rate is lowered to 10 

seconds and the time delays for dim-to-off functionality is reduced. The faster response allows the sensor operation to be quickly verified on 

site. If test mode is activated for a closed loop daylight sensor, it must be manually deactivated when the test is completed. Test mode will not 

automatically shut off. 

Note

: If the device allows dim-to-off, when the measured light level exceeds 150% of the calibrated light level for more than 30 seconds, the sensor will 

turn lighting OFF. Lighting will be turned back ON when one of the two conditions occurs. Condition 1: The measured light level falls between 100% and 

50% of the calibrated light level for more than 20 seconds. Condition 2: The measured light level falls below 50% of the calibrated light level for longer 

than 5 seconds 

 
To use test mode: 
1: Bring the mobile device within range (within 60 feet) of any provisioned WaveLinx Lite device in the desired area. 
2: Ensure that the mobile device Bluetooth is turned on, and then open the WaveLinx Lite Mobile Application. 
3: In the site list, select a site. 
4: In the area list, select the desired area and verify that there is a network connection. 
5: In the zone list, select the desired zone. 
6: In the list of devices, locate the daylight sensor device. If needed, use the identify icon ‘ ‘ to flash the loads until the correct one is 

found, and then tap the device to open the device details. 

 

7: Tap ‘Daylight Sensor’ at the top of the device details pages to open to the daylight sensor view. 
8: Slide the switch next to ‘Test Mode’ to the ON position and proceed to test the sensor. 

 

 

 

 

Select the area 

If needed, use ‘identify’ to 

locate the correct device 

Tap device to open 

the device details 

Select a zone 

Select the site 

Verify network 

connection 

Connected 

Not connected 

Tap ‘Daylight 

Sensor’ 

Slide ‘Test Mode’ switch to 

activate or deactivate 

Test mode ON 

Test mode OFF 

Remember to slide ‘Test Mode’ switch to the OFF position once the test is complete. Test mode does not 

automatically time out. 

Summary of Contents for WaveLinx Lite















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands