background image

            Caution: Risk of fire/

            flammable materials

(Required for R32/R290 units only)

Warning: low burning

velocity material

(For R32 models apply to 

IEC60335-2-40:2018)    

 

   precautions shall be complied with prior to conducting work on the system.

2)Work procedure

   Work shall be undertaken under a controlled procedure so as to minimise the risk of a flammable gas 

   or vapour being present while the work is being performed.

6.Information on servicing

1)Checks to the area

   Prior to beginning work on systems containing flammable refrigerants, safety checks are necessary to 

   ensure that the risk of ignition is minimised. For repair to the refrigerating system, the following 

   

1.Transport of equipment containing flammable refrigerants 

   See transport regulations

2.Marking of equipment using signs

   See local regulations

3.Disposal of equipment using flammable refrigerants

   See national regulations.

4.Storage of equipment/appliances

  The storage of equipment should be in accordance with the manufacturer's instructions.

5.Storage of packed (unsold) equipment

  Storage package protection should be constructed such that mechanical damage to the equipment 

  inside the package will not cause a leak of the refrigerant charge. The maximum number of pieces of 

  equipment permitted to be stored together will be determined by local regulations.

Explanation of symbols displayed on the unit(For the unit adopts R32/R290 Refrigerant only):

WARNING

CAUTION

CAUTION

CAUTION

This symbol shows that this appliance used a flammable refrigerant. If the refrigerant 

is leaked and exposed to an external ignition source, there is a risk of fire.

This symbol shows that the operation manual should be read carefully.
This symbol shows that a service personnel should be handling this equipment 

with reference to the installation manual.
This symbol shows that information is available such as the operating manual or 

installation manual.

AVERTISSEMENT 

Ne pas utiliser de produits permettant d’accélérer le dégel ou de produits de nettoyage autres que 

ceux recommandés par le fabricant. 

L’appareil doit être entreposé dans un endroit sans source d’allumage fonctionnant en continu (par 

exemple : flamme nue, appareil au gaz en marche ou radiateur électrique en marche). 

Ne pas percer ni bruler. 

Attention : les frigorigènes peuvent être inodores.

Safety 

Precautions

  

 

 Page  5

Summary of Contents for CH-STLS-14AC































Reviews: