SYSTEM PROGRAMMING AND SETTING
36
6.2.10 Setting CAN-bus signals for system arming/disarming (only for model Convoy iGSM-005 CAN)
Depending on car brand/model CAN-bus can have signals of CL closing/opening and CL status signal. It is
necessary to choose the required signal type for proper system control. To set signal type enter the following
command in SMS-text (see clause 2.3):
CANARM x
where
х
= 0 – CAN-bus signals for system arming/disarming are not used
x
= 1 - signals of CL closing/opening using regular transmitter are used
x
= 2 - CL status signal (regular security system) is used
Default setting – 1.
ATTENTION!
When you have per f or med settings procedure, remove safety jumper t o exclude unpurposed hardware
settings changes by the user.
6.3 Hardware-controlled settings using service button
You can set system hardware settings using service button and main unit speaker, which sounds allow you
to control button pressing, current status of changeable functions and their setting.
Speaker can play the following signals
•
«SHORT BEEP»
(
) – pressing service button
•
«LONG BEEP»
(
) – entering of 0 digit
•
«SHORT TRILL»
(
) – function number digit or function value digit is entered
•
«LONG TRILL»
(
) – entering system hardware settings mode
•
«KU-KA-RE-KU»
(
) – new function value record is done and return to function number entering mode
•
«BOOM»
( ) – return to function number entering mode without new function value record
•
«BOO-BOO-BOO-BOOM»
(
) – entering of wrong PIN-code or wrong new function value
•
«STAIRS»
(
) – exiting system hardware settings mode
6.3.1 Digits input using service button
Entered figure can consist of one or several digits. Digit is entered with consecutive short (or long – 0
digit) pressings. Speaker short sound controls every pressing
«SHORT BEEP»
. When long pressing despite
sound “
SHORT
BEEP
” second signal “
LONG BEEP
” seconds which means that digit 0 is entered (previous
short pressings are canceled when this digit is pressed). Pause between buttons pressing should not exceed
1 second. Pause between 1 and 2 seconds means that current digit is already done (speaker will play sound
“
SHORT TRILL
”). If pause after pressing is longer than 2 seconds, module will finish entering of whole figure
(speaker will play sound depending on mode).
Example:
Function 301 number entering
The specified function number is entered in the following way:
1. Press service button shortly 3 times consecutively (digit 3).
When pressing you will hear «
SHORT BEEP
» signal, in 1 second after button release you will hear
«
SHORT TRILL
» signal.
2. Press and hold service button for more than 2 seconds (digit 0)
When pressing you will hear «
SHORT BEEP
» signal, in 1 second after pressing you will hear «
LONG
BEEP
» signal, in 1 second after button release you will hear «
SHORT TRILL
» signal.
3. Press service button once (digit 1)
When pressing you will hear «
SHORT BEEP
» signal, in 1 second after button release you will hear
«
SHORT TRILL
» signal.
4. In 4 seconds after button release you will hear signal «
KU-KA-RE-KU
».
=301
«3»
наст
ройк
и
«0»
наст
рой
ки
№
заводское
(
максима
льное
)
установлен
ное
ед
.
6
5(20)
секун
«1»
наст
рой
ки
№
заводское
(
максима
льное
)
установлен
ное
ед
.
6
5(20)
секун
If incorrect function number is entered signal
«BOOM»
will sound (function absent).
