SYSTEM PROGRAMMING AND SETTING
32
Performing of GSM-system arm and disarm
Input
Function of input
Description of input work
IN1 (green)
Arm
If input
IN1
has a signal and input
IN3
does not have a signal GSM-
system w ill ac tivat e the arm mode. This signal in arm mode (no
earlier than 2 seconds af ter the system is armed) will cause
deactivation of all sensors – see sub-item 3.2.1. Input
IN1
should be
connected to regular actuator (interface) of central lock of the car
or to the channel of additional security system
IN4 (white-black)
Arm sign
Input
IN4
should be connected to output «arm sign» of additional
security sys t em. It allows both arming and disarming. Input
condition does not depend on permission signals of input
IN8
, but it
depends on prohibition signal of input
IN2
IN3 (blue)
Disarm
If input
IN3
has a signal and input
IN1
does not have a signal GSM-
system will deactivate the arm mode. Input
IN3
should be connected
to regular actuator (interface) of central lock of the car or to the
channel of additional security system
IN2 (green-red)
Arm prohibition
If input
IN2
has a signal system will ignore arm signals of
IN1
input
(arm mode can be activated only through the phone). Input
IN2
, for
example, can be connected to sensor of driver’s presence in the car
cabin
Blue (green) of 4-pin
connector of additional
sensor
(only for iGSM-005)
Disarm prohibition
When signal (ground) appears in this input system ignores signal of
arm of channel
IN1
, and signal of disarm of channel
IN3
IN8 (blue-red)
Arm/disarm
permission
If input
IN8
has a signal it is permitted during 2 seconds
to arm and disarm system through inputs
IN1
and
IN3
.
Input
IN8
should be connected, for example, to circuits of
regular light indication of the car, signals of which confirm
closing and opening of regular central lock
IN7 (yellow-black)
Disarm
confirmation
If input
IN7
has a signal after GSM-system is disarmed, it
deactivates all lockouts (if «Immobilizer» mode is activated
– see item 3.4). Appearing of signal of this input during
30 seconds after disarming cancels notifying of the
programmed users (see items 4.4, 6.1.4)
To adjust system universal input enter the following command in SMS text (see item 2.3):
INx y z f m n
where
х
= (1 – 8) – input number
y
= (+/–) – input signal polarity
z
= (1, 2) – input type (1 – input actuates when closing, 2 – when opening)
f
= (0 - 12) – universal input function (0 – special function)
m
= (1 - 100) – time to ignore input close on «ground» or +12V (1 = 0.1 sec; 2 - 0.2 sec…100 = 10 sec. On
default – 0.1)
n
= (10- 100) – time to ignore input open from «ground» or +12V (1 = 0.1 sec; 2 - 0.2 sec…100 = 10 sec.
On default – 0.1)
Note
Parameters m, n can miss. In this case system will setup default settings of these parameters.
Af ter receipt of SMS with this command, GSM-system will send SMS report:
INx y z,f,m,n
Special functions list (f = 0) for system universal inputs:
IN1
– arm
IN2
– arm prohibition
IN3
– disarm
IN4
– arm sign
IN5
– auto start control
IN6
– trunk lock actuator
IN7
– button conforming disarming
IN8
– arm/disarm permission
