Control Microsystems SCADAPack 350 Hardware Manual Download Page 60 | Manualshive

Page: 60 / 64

background image

Status

Power Mode LED
Run LED
Status LED (shows functional status)
Forced I/O LED

Digital Inputs / Outputs

8 LEDs

Counters

3 LEDs

LAN

Link indicator (LINK) LED
Activity indicator (ACT.) LED

Push-button

LED power toggle

16.6 Power

Supply

DC power Input

30V maximum
10.0 to 11.5V turn on
9.5V typical turn off
12mW at 12V during Sleep
510mW at 12V during normal operation. 32MHz., LEDs off, no
expansion, LAN and USB disabled.
320mW at 12V during reduced power mode operation. 12MHz.,
LEDs off, no expansion, LAN and USB disabled. (Reduced power
mode)
1.2W at 12V during normal operation. 32MHz., LEDs off, no
expansion, LAN enabled and USB disabled.
Add 25 to 100mW when enabling the LEDs.
12W at 24V maximum. 5V supply fully loaded and Vloop on and
boosted, fully loaded.

Output capacity

5V at 1.2A capacity
5V at 80mA required by 5209 controller (LAN and USB disabled)
5V at 40mA required by 5209 controller (LAN and USB disabled)
in reduced power mode.
5V at 160mA required by 5209 controller to enable the LAN
5V at 50mA required by 5209 controller to enable the USB
5V at 1.1A (current limited) for COM2 and I/O expansion
5V at 250mA (current limited) on COM3 for Vision displays
5V at 100mA (current limited) for USB downstream port loads
Vloop: 24V at 0.14A available for the 5 analog inputs and 2
optional analog outputs

Efficiency

85%, 12Vdc input, full load

16.7 I/O

Capacity

5000 Series I/O
Expansion
Capacity

Maximum 40 I/O modules.
Refer to the System Configuration Guide for further details.

SCADAPack 350 Hardware Manual
February 14, 2007

59

«
...
58
59
60
61
62
...
»

Summary of Contents for SCADAPack 350

































































Reviews:

No comments

Related manuals for SCADAPack 350

Brand: Radio Shack Pages: 52

Brand: Lawler Pages: 2

Brand: Eaton Pages: 86

Brand: UniKey Pages: 20

Brand: S-COM Pages: 400

Brand: Calsense Pages: 74

Brand: EasySMX Pages: 11

Brand: EasySMX Pages: 8

Brand: Wang Pages: 68

Brand: NAVITAS Pages: 14

Brand: Eaton Pages: 448

Brand: Eaton Pages: 57

Brand: IN-COMMAND Pages: 47

Brand: SYCLOPE Pages: 60

Centronic SunWindControl SWC245-II

Brand: Becker Pages: 52

Brand: Sartorius Pages: 165

TITAN-TRACKSIDE-3

Brand: Remote Control Systems Pages: 4

Brand: OmarLift Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands