Control Microsystems SCADAPack 350 Hardware Manual Download Page 35 | Manualshive

Page: 35 / 64

background image

Pin

Function

Description

(Input)

The LED is lit for a MARK level.

6 TxD

(Output)

The level is SPACE on standby and MARK for transmitted
data.
The LED is lit for a MARK level.

7 CTS

(Input)

This level must be a MARK for the communication port to
transmit data. When the attached device does not provide this
signal, the controller keeps the line at a MARK.
When the attached device does provide this signal, it must set
CTS to MARK to allow the controller to transmit data.

8 RTS

(Output)

This pin is a MARK if full-duplex operation is selected for the
port.
This pin is set to a MARK just before and during transmission
of data if half-duplex operation is selected.
This pin is set to a SPACE when no data is being transmitted.
The LED is ON for a MARK level.

SCADAPack 350 Hardware Manual
February 14, 2007

34

«
...
33
34
35
36
37
...
»

Summary of Contents for SCADAPack 350

































































Reviews:

No comments

Related manuals for SCADAPack 350

Brand: Rayrun Pages: 2

Brand: IDenticard Pages: 2

Brand: 3Ware Pages: 2

Brand: UniKey Pages: 20

Brand: GBD Pages: 68

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 8

Brand: Salda Pages: 20

Brand: Ascon tecnologic Pages: 16

Brand: KIOUR Pages: 3

Brand: Topway Pages: 14

Brand: Wave Home Solutions Pages: 15

Brand: BabyActive Pages: 4

IntelliCross TouchFree Kit

Brand: Novax Pages: 3

Brand: Daikin Pages: 19

Brand: Forcepoint Pages: 15

VPPM-...-LK Series

Brand: Festo Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands