Control Microsystems SCADAPack 350 Hardware Manual Download Page 6

Page: 6 / 64

16.6

Power Supply ............................................................................................... 59

16.7

I/O Capacity ................................................................................................. 59

16.8

Analog Inputs ............................................................................................... 60

16.9

Analog Outputs ............................................................................................ 60

16.10

Counter Inputs.............................................................................................. 61

16.11

Digital Inputs/Outputs................................................................................... 61

APPROVALS AND CERTIFICATIONS ....................................................... 63

Index of Figures

Figure 1: SCADAPack 350 Controller....................................................................................7

Figure 2: SCADAPack 350 Layout.......................................................................................10

Figure 3: Power Management..............................................................................................13

Figure 4: Analog Input Wiring ..............................................................................................18

Figure 5: Analog Output Wiring............................................................................................19

Figure 6: Digital Input/Output Wiring....................................................................................24

Figure 7: Counter Input Wiring.............................................................................................25

Figure 8: Counter Jumpers ..................................................................................................28

Figure 9: RJ-45 Connector Pinout ......................................................................................30

Figure 10: RJ-45 Connector Pinout ....................................................................................33

Figure 11: RS-232 DTE to RS-232 DTE without Handshaking............................................35

Figure 12: RS-232 DTE to RS-232 DTE with Handshaking.................................................35

Figure 13: RS-232 DTE to RS-232 DCE With Handshaking ...............................................36

Figure 14: COM2 RJ-45 Connector .....................................................................................40

Figure 15: RS-485 Wiring ....................................................................................................41

Figure 16: RJ-45 Connector for Ethernet.............................................................................44

Figure 17: Host USB Port Connections ...............................................................................45

Figure 18: Peripheral USB Port Connections ......................................................................45

SCADAPack 350 Hardware Manual
February 14, 2007

Summary of Contents for SCADAPack 350

































































Search results

Summary of Contents for SCADAPack 350

Reviews:

Related manuals for SCADAPack 350

Brands by name

Popular brands

Control Microsystems SCADAPack 350, Hardware Manual

Search results

Summary of Contents for SCADAPack 350

Reviews:

Related manuals for SCADAPack 350

Brands by name

Popular brands