Control Microsystems SCADAPack 350 Hardware Manual Download Page 58

Page: 58 / 64

16 Specifications

Disclaimer: Control Microsystems reserves the right to change product specifications without
notice. For more information visit

www.controlmicrosystems.com

16.1 General

I/O Terminations

6 and 12 pole, removable terminal blocks.
12 to 22 AWG
15A contacts

Dimensions

8.40 inch (213mm) wide
5.00 inch (127 mm) high
1.80 inch (45mm) deep

Packaging

Corrosion resistant zinc plated steel with black enamel paint

Environment

5% RH to 95% RH, non-condensing
–40

C to 70

–40

F to 158

16.2 Controller

Processors

32-bit ARM7-TDMI microcontroller, 32 MHz clock
integrated watchdog timer
Two Microcontroller co-processors, 20 MHz clock

Memory

16MBytes FLASH ROM
4MBytes CMOS RAM
4kBytes EEPROM

Non-volatile
RAM

CMOS RAM with lithium battery retains contents for 2 years
with no power

Clock calendar

1 minute/month at 25°C

+1/–3 minutes/month 0 to 50°C

Internal
temperature

Measurement range -40°C to 75°C. Accuracy

5°C.

Measurement range -40°F to 167°F. Accuracy

9°F.

Lithium battery
Monitor

Accuracy

0.2V.

Power Input
Voltage Monitor

Accuracy

0.4V.

16.3 Communications

Communication
Port COM1

RS-485 serial port
removable terminal block
Two-wire half duplex
Bias resistors installed.

Communication
Port COM2

Jumper configurable RS-232 or RS-485
RS-232 compatible serial port (

5V)

Data Terminal Equipment (DTE)
8 pin modular jack

SCADAPack 350 Hardware Manual
February 14, 2007

Summary of Contents for SCADAPack 350

































































Search results

Summary of Contents for SCADAPack 350

Reviews:

Related manuals for SCADAPack 350

Brands by name

Popular brands

Control Microsystems SCADAPack 350, Hardware Manual

Search results

Summary of Contents for SCADAPack 350

Reviews:

Related manuals for SCADAPack 350

Brands by name

Popular brands