Control Microsystems SCADAPack 350 Hardware Manual Download Page 28 | Manualshive

Page: 28 / 64

background image

9.2.2

Connecting to Higher Voltage Turbine Meters

Counter inputs 1 and 2 inputs can also be configured for use with a turbine meter featuring an
integrated or standalone amplifier. In this configuration, the SCADAPack’s internal amplifiers must
be bypassed.

For Counter 1:

5.

Install jumper J11 in the ‘Ext Position’.

6.

Remove jumpers J9 from the ‘See J11’ position and install on the other two pins.

For Counter 2

1.

Install jumper J12 in the ‘Ext Position’.

2.

Remove jumpers J10 from the ‘See J12’ position and install on the other two pins.

Refer to the figure below for an illustration.

J9

J11

Counter 1 input

Internal 1000

ohms connected

to Input Voltage

J10

J12

Counter 2 input

Internal 1000

ohms connected

to Input Voltage

12V DC

SCADAPack 350

Ext. Amplifier

Ext. Amplifier

See J11

See J12

Figure 10: Setting Counter Input 1 and 2 for Turbine Meters with amplified signals

Your standalone amplifier may have a specific current requirement as specified by the manufacturer.
As shown in the figure above, the SCADAPack 350 includes a 1000-ohm resistor from the counter
input to the DC input power source, when the jumpers J11 and J12 are installed in the ‘Ext
Amplifier’ position, as described above. The above configuration is the recommended wiring for a
Halliburton Low Power Pre-Amp, when the SCADAPack 350 is

powered from 12V

.

SCADAPack 350 Hardware Manual
February 14, 2007

27

«
...
26
27
28
29
30
...
»

Summary of Contents for SCADAPack 350

































































Reviews:

No comments

Related manuals for SCADAPack 350

Brand: GE Pages: 2

Brand: XOXO Modular Pages: 13

Brand: Saitek Pages: 13

Brand: Balboa Water Group Pages: 28

Brand: UE Pages: 4

Brand: UE Pages: 4

Brand: XBOX Pages: 7

Brand: Handicare Pages: 56

Brand: Tapeswitch Pages: 13

Harmony Controller 2000

Brand: A10 Pages: 27

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

PowerXL DX-NET-ETHERCAT-2

Brand: Eaton Pages: 3

Brand: Fairchild Pages: 2

Brand: Fairford Pages: 233

Brand: tams elektronik Pages: 12

Brand: Lattice Pages: 23

Brand: Lattice Semiconductor Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands