Control Microsystems SCADAPack 350 Hardware Manual Download Page 43 | Manualshive

Page: 43 / 64

background image

11 Ethernet

Communication

The SCADAPack 350 controller has one 10/100Base-T Ethernet port. This is a single
communications channel running at 10/100 Mb/s over unshielded, twisted - pair cabling, using
differential signaling. It supports both half-duplex and full-duplex operation. The interface supports
auto-negotiation for both the speed and half/ full-duplex mode selection.

11.1

LAN Port Settings

Connections to the LAN port are made through a RJ-45 modular connector. The wiring and pin
connections for this connector are described in section

RJ-45 Modular Connector for

Refer to section

Field Wiring

for the location of the LAN port on the SCADAPack controller

board.

11.1.1 TCP/IP

Settings

The following table shows the TCP/IP parameters supported by the LAN port. These parameters are
set from the ISaGRAF Workbench or from an application program running in the controller. Default
values are set when a Cold Boot is performed on the controller.

Parameter

Supported Values

IP Address

In the format 255.255.255.255
Default: 0.0.0.0

Subnet Mask

In the format 255.255.255.255
Default: 255.255.0.0

Gateway

In the format 255.255.255.255
Default: 0.0.0.0

The

IP Address

is the address of the controller. The IP address is statically assigned. Contact your

network administrator to obtain an IP address for the controller.

The

Subnet Mask

is determines the subnet on which the controller is located. The subnet mask is

statically assigned. Contact your network administrator to obtain the subnet mask for the controller.

The

Gateway

determines how your controller communicates with devices outside its subnet. Enter

the IP address of the gateway. The gateway is statically assigned. Contact your network
administrator to obtain the gateway IP address.

11.1.2 Modbus/TCP

Settings

The following table shows the Modbus/TCP parameters supported by the LAN port. These
parameters are set from the ISaGRAF Workbench or from an application program running in the
controller. Default values are set when a Cold Boot or Service Boot is performed on the controller.

Parameter

Supported Values

Master Idle Timeout

Any value in seconds.
Default: 10 seconds

Server Receive Timeout

Any value in seconds.
Default: 10 seconds

Maximum Server
Connections

Valid values are 1 to 20.
Default: 20

SCADAPack 350 Hardware Manual
February 14, 2007

42

«
...
41
42
43
44
45
...
»

Summary of Contents for SCADAPack 350

































































Reviews:

No comments

Related manuals for SCADAPack 350

Brand: OmarLift Pages: 14

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Danfoss Pages: 37

Brand: Daikin Pages: 44

Brand: VAT Pages: 26

Brand: Jands Pages: 7

Brand: hager Pages: 11

coviva Smartbox TKP100A

Brand: hager Pages: 34

Brand: Jandy Pages: 28

Brand: Jands Pages: 6

Grafica DNE-K07

Brand: Paradox Pages: 24

Brand: Panosol Pages: 105

Brand: Pangolin Pages: 8

Brand: Vacon Pages: 50

Brand: V2 Pages: 116

Brand: V2 Pages: 8

Brand: V2 Pages: 25

Brand: V2 Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands